Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 04-02-2011, 10:04 AM
Rental Limo's Avatar
Rental Limo Rental Limo is offline
VideoKarma Member
 
Join Date: Jan 2008
Location: Cudahy, Wisconsin
Posts: 126
Philco Predicta Television In Racine, Wisconsin

http://milwaukee.craigslist.org/atq/2299138711.html

Price is kinda high though.
Reply With Quote
  #2  
Old 04-02-2011, 10:30 AM
charokeeroad's Avatar
charokeeroad charokeeroad is offline
John Q
 
Join Date: Sep 2010
Location: Southern California, IE
Posts: 644
Looks pretty, wonder if the CRT is good?
Reply With Quote
  #3  
Old 04-02-2011, 10:32 AM
50scraze's Avatar
50scraze 50scraze is offline
VideoKarma Member
 
Join Date: Oct 2009
Posts: 77
Predictas are the most over priced sets. The cool space age look is really all its about.
Reply With Quote
  #4  
Old 04-02-2011, 10:45 AM
charokeeroad's Avatar
charokeeroad charokeeroad is offline
John Q
 
Join Date: Sep 2010
Location: Southern California, IE
Posts: 644
I tested the CRT on three Predictas out here in southern California over the last six months. All the CRTs were dead or close to it.
Reply With Quote
  #5  
Old 04-02-2011, 02:59 PM
GeorgeJetson's Avatar
GeorgeJetson GeorgeJetson is offline
VideoKarma Member
 
Join Date: Nov 2010
Location: The future (circa 1957-1961)
Posts: 443
That was one of the biggest problems with the Predictas.
almost all the 21" sets have bad picture tubes,the smaller 17" predictas seem to fare better.
__________________
No wonder this circuit failed,it says "made in Japan"!
Reply With Quote
Audiokarma
  #6  
Old 04-02-2011, 06:17 PM
dieseljeep dieseljeep is offline
VideoKarma Member
 
Join Date: Jul 2010
Posts: 7,562
Quote:
Originally Posted by GeorgeJetson View Post
That was one of the biggest problems with the Predictas.
almost all the 21" sets have bad picture tubes,the smaller 17" predictas seem to fare better.
That model doesn't interest me at all. The only predicta that interests me is the 17" table model with the power transformer. The CRT's are easier to get too. There's plenty of those lousy seventeener III's around with good CRT's.
Reply With Quote
  #7  
Old 04-02-2011, 08:04 PM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
I like my predicta a lot. its the 17" princess, red with white front and gold trim, with the trim CRT arms. I know a lot of people dont like them, but I found mine to be easy to work on. its very modular so you can pull the chassis and work on it. I did all the cap replacing without pulling the main pcb. There were a few that required bending my soldering gun tip, but for the most part is was no big deal. I don't think I would care for the holiday model as I prefer the transformer chassis as well.
Reply With Quote
  #8  
Old 04-02-2011, 10:18 PM
marty59's Avatar
marty59 marty59 is offline
VideoKarma Member
 
Join Date: May 2008
Location: Arlington, Tx
Posts: 915
My Sencore CR161 tester was very kind to my 21" barber pole CRT but you must use the lowest settings possible for these low filament voltage tubes and keep your fingers crossed! And I can understand, these sets may not be for everybody and especially to work on. I like it though.

Mine was given/saved for me quite a while back so it has a special value. Even though it now works, I still need to finish it up. The contrast pot is bad and I need to add an in-rush current limiter, make a new base for the cabinet, etc.
Reply With Quote
  #9  
Old 04-05-2011, 08:55 PM
GeorgeJetson's Avatar
GeorgeJetson GeorgeJetson is offline
VideoKarma Member
 
Join Date: Nov 2010
Location: The future (circa 1957-1961)
Posts: 443
I like all the Predicta models,but my favorites are the Stereo Tandem in blonde and the Danish Modern model.

My favorite of the 17" models would have to be the siesta model with built in clock.

One day I want to find a blonde stereo tandem.
__________________
No wonder this circuit failed,it says "made in Japan"!
Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:15 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.