![]() |
|
#106
|
|||
|
|||
|
Did that a few steps back, didn't stop the flicker.
|
|
#107
|
||||
|
||||
|
Quote:
|
|
#108
|
|||
|
|||
|
Question:
I have learned a good bit in a short time, especially since I had to do the full recap. Before I start trying to really adjust and try to solve these continuing problems, what I could do is test the chassis components following the service guide. Use/learn the oscope, vtvm, create test pads with apropriate resistors, adjust the tuner to the proper mc readings, the picture and sound circuits, make sure the waves are correct, etc. Would that potentially solve future problems? To service the set the way it would have been, would that insight add more to my knowledge base? |
|
#109
|
||||
|
||||
|
Quote:
The one exception to the above is tuner oscillator adjustment (which should center fine-tuning on channel)....your set could benefit from that and you can usually do it without significantly affecting alignment....there are almost as many different TV tuner designs as there are chassis so you need to read the manual carefully to find the correct procedure and adjustment points. Count the turns you make so if you were adjusting the wrong thing you can get it close to where it was. Most schematics list voltages at the tube sockets anything more than 30% away from documented is likely an indication of fault. Note these voltages skew with the wall voltage in your house so if the B+ is 10% off so will be everything else...I often plug my sets into a variac and adjust the input voltage for the highest B+ rail derived from the power transformer/rectifier to be exactly what the schematic says so I don't have to factor a B+ skew into determining what the tolerance is in the socket measurements. If measuring voltages on a live set work with one hand in your pocket and avoid getting shocked... Safety first. You can sometimes find socket resistance charts which can also be helpful. Scope work is often unnecessary once a set is as far along as yours is, but if you want to play around with a scope and learn how to see waveforms you can. I generally use my scope for adjusting H osc waveforms, looking for hum or other pronounced non-random noise, and when I suspect a waveform in a circuit is badly wrong and want to know exactly how it's wrong to gain insight into what is happening. One thing I like to do when it isn't safe or practical to reach a test point with the set running is to take a couple of leads with small alligator clips on both ends and use those to hook the meter up with the set off then switch on the set. You can also get tube socket extenders but they are expensive and don't always match a needed test point. If tubes test good and capacitors are new but a stage is performing badly the next thing I usually suspect is out of tolerance resistors...some circuits with large adjustment range like vertical I try to adjust first before worrying about resistors....the vertical could have been adjusted to compensate for a bad tube or leaking capacitor that you changed and now needs readjustment for good parts.
__________________
Tom C. Zenith: The quality stays in EVEN after the name falls off! What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4 Last edited by Electronic M; 07-19-2020 at 12:28 PM. |
|
#110
|
|||
|
|||
|
The vertical has a fold over at the bottom, fold is probably 4" on average, a black line appears near the center of the screen that should be the extreme bottom mask.
Last edited by BandDirector; 07-19-2020 at 08:23 PM. |
| Audiokarma |
|
#111
|
||||
|
||||
|
There's a big usually low voltage lytic on the cathode of the vertical output in most sets that can cause that...did you replace it?
__________________
Tom C. Zenith: The quality stays in EVEN after the name falls off! What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4 |
|
#112
|
|||
|
|||
|
I'd have to pull the chassis to look, but I don't remember a specific lytic for vertical. I can't recall which one is which, I'll look on the schematic. The lower 4 electro's are near the vertical line and height are near them, could be one of those that are 20 and 30 mfd at 50 volt. But those are new.
Last edited by BandDirector; 07-19-2020 at 09:35 PM. |
|
#113
|
||||
|
||||
|
I see 2 pictures... looks like the vertical is running at half frequency.
jr |
|
#114
|
|||
|
|||
|
Quote:
How do you fix that? I've swapped vert osc and vert drive tubes and it isn't that. |
|
#115
|
||||
|
||||
|
Quote:
Double check the values of the vertical stage film caps you changed and change any resistor that measures outside of its marked tolerance. The cathode lytic in the vertical of most sets is a 25-100V 80-300uF lytic. Are you good enough at reading a schematic to differentiate the symbols for heater, cathode, grid, and plate? If so look at the vertical tube that drives the vertical output transformer and identify it's cathode and look for a lytic connected to the cathode. The half frequency issue may be the only problem but if the foldover on the bottom persists after fixing the frequency issue check that lytic first.
__________________
Tom C. Zenith: The quality stays in EVEN after the name falls off! What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4 |
| Audiokarma |
|
#116
|
||||
|
||||
|
Here's the vert circuit. Looks like the vert out cathode is direct to ground, so no cathode bypass cap(electrolytic). My money is on an incorrect value film cap too.
https://live.staticflickr.com/65535/...02e09742_b.jpg |
|
#117
|
|||
|
|||
|
It is certainly possible I made a mistake, I did have to go back and switch out a few caps because I would forget the 0 multiplier when reading values.
|
|
#118
|
||||
|
||||
|
That's a pretty common thing. Are you using Sams 400 folder 4 for reference or something else?
|
|
#119
|
|||
|
|||
|
I have an original field service guide, my local shop doesn't have that photofact. I do have a schematic for this chassis in the service manual.
|
|
#120
|
||||
|
||||
|
That's probably even better because Sams changes the part location designation from the manufacture, although their photos are handy for locating components.
|
| Audiokarma |
![]() |
|
|