Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Solid State CRT Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 11-29-2022, 09:36 AM
zeno's Avatar
zeno zeno is offline
VideoKarma Member
 
Join Date: Mar 2013
Location: New Hampshire
Posts: 4,918
Quote:
Originally Posted by radiotvnut View Post
I think the best System 3 chassis was the first one with the 9-153 horizontal sweep/HV module and I don't recall running into a bad flyback on one of those, but those didn't get all of the operating voltages for the set from the flyback and that likely put less stress on the flyback.
Agree. Probably the most reliable Zenith built. And the BEST greens of any set.
Cold joints at Hoz drive transformer were 90% of the fails. After that
just a scattering of odds & ends.
A little more on CC2 XXX chassis ( S-3 style) & System 3
A few late J line high end 25" sets were built with the new XXX chassis.
They were NOT marked System 3.
K line System 3 came out on all but the leader models. System 3
was just a feature list. If it had the full list it was called a S-3.
J & K line were first gen XXX chassii , still had PWR transformer
and a normal H drive & output design.
L-line starts gen 2 XXX chassis. Transformer gone, replaced by a
complex H drive & out. They could also shoe horn it into a 13".

Why no FBT's supplied ? For us a 9-160 module net exchange
was $66. Buying a similar FBT, H out & a hand full of small parts would
approach that. But swapping the board takes maybe 4 mns & a
complete repair 15 mns. So a lower labor rate & total cost is
about the same.

Last the spark gap. It belongs in the hall of Zenith fame. We saw
many sets in for a different reason with blasted gaps. Normally
on a modern set seeing that throws up a stop sign. You will
often have a totaled set on your hands.

enuf fer now
73 Zeno
LFOD !
Reply With Quote
  #2  
Old 11-29-2022, 09:10 PM
radiotvnut's Avatar
radiotvnut radiotvnut is offline
VideoKarma Member
 
Join Date: Jul 2007
Location: Meridian, MS
Posts: 6,025
Quote:
Originally Posted by zeno View Post
Agree. Probably the most reliable Zenith built. And the BEST greens of any set.
Cold joints at Hoz drive transformer were 90% of the fails. After that
just a scattering of odds & ends.
A little more on CC2 XXX chassis ( S-3 style) & System 3
A few late J line high end 25" sets were built with the new XXX chassis.
They were NOT marked System 3.
K line System 3 came out on all but the leader models. System 3
was just a feature list. If it had the full list it was called a S-3.
J & K line were first gen XXX chassii , still had PWR transformer
and a normal H drive & output design.
L-line starts gen 2 XXX chassis. Transformer gone, replaced by a
complex H drive & out. They could also shoe horn it into a 13".

Why no FBT's supplied ? For us a 9-160 module net exchange
was $66. Buying a similar FBT, H out & a hand full of small parts would
approach that. But swapping the board takes maybe 4 mns & a
complete repair 15 mns. So a lower labor rate & total cost is
about the same.

Last the spark gap. It belongs in the hall of Zenith fame. We saw
many sets in for a different reason with blasted gaps. Normally
on a modern set seeing that throws up a stop sign. You will
often have a totaled set on your hands.

enuf fer now
73 Zeno
LFOD !
I think I remember seeing one of those late "J-line" consoles with the "System 3" chassis, but the set was still labeled as "solid state = chromacolor II."

I have "K" 19" motel set with AM/FM radio and it uses the modular CC2 chassis, paired with an inline EFL tube.

I also have one of the last 19" delta-gun CC2 sets from '78 and it is obviously a "loss leader" set. No AFC button, no Chromatic button, just a power button and the two channel knobs.
Reply With Quote
  #3  
Old 12-14-2022, 04:52 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
My dad had one of these sets from 1985 (Green LED Channel Readout) and it worked really well for many years until it finally died (the TV Shorted out when I was trying to tweak some of the picture settings on the back.)

The original remote on my dad's TV took the old J-Battery, which was no longer available after the early 2000s, so then we just used the VCR remote with it, which was one of the first Goldstar made Zenith VCRs made in 1990 after Zenith stopped having JVC make their VCRs.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:34 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.