![]() |
|
|
|
#1
|
||||
|
||||
|
Quote:
![]() I used to work at the RCA Smirnoff Labs in princeton NJ back then, and the CTC101 flyback problem was due to them trying to skimp on the number of HV diodes in the flyback. The very high voltage secondary was split into 6 segments and diodes were to be placed between sections, and a final diode that would feed the fat red wire to the CRT. Ground-w1-d1-w2-d2...d5-w6-d6-fat red wire. But they tried to cost reduce this scheme, by skipping some of the diodes. Which made for twice the AC voltage per diode, and twice the AC voltage on some of the terminals inside the big epoxy lump on the side of the transformer. This became a warrenty nightmare for RCA... All the new replacements had 6 diodes. Which helped a lot, though I had a CTC101 and the replaced flyback did die around 1990. It was a great set before that happened. Had the comb filter for better chroma luma separation. It had a partially hot chassis, the horizontal part of the yoke was "hot", but the vertical part was "cold", along with the tuner, IF strip, audio output and CRT video amp driver circuits. The "cold" supply was derrived from separate secondaries on the flyback.
__________________
|
|
#2
|
|||
|
|||
|
Interesting stuff on the 90s RCAs, but I don't really care. Anything made after 1990, as well as all other electronic makers besides RCA, is considered to be cheaply made, and most will not exceed 20 years. 1980s-made all the way.
Looks like 1983-1984 might be the highest peak quality year for RCA. Now, my only trouble is, what VCR should I put for my CTC-121 TV? Should I put in a Panasonic-made 1982 top-loading RCA VGT650 4-head Dolby stereo or Hitachi-made 1983 RCA VJT700 4-head Dolby stereo? I am determining right now which of the two Japanese makers could make a VCR for me that can run for another 60 years from today (excluding belt changes) until I die. Hmm, Panasonic or Hitachi? Each has its own pros and cons. Would you go for Panasonic or Hitachi?RCA VKT650 is a really bad VCR in terms of design, and it is definitely not worth repairing (IMO) when it first breaks. I collected more than 25 top-of-the-line vintage Hi-Fi VHS VCRs, and the RCA VKT650 is the most disappointing I have seen. It uses a lot of surface-mount capacitors on the video board, which is completely unacceptable to put on in 1984, but what's 10 times worse, the board was sealed with black covering hard glue all over around, and all technicians I spoke with will not service this board. They would need to order a new board. Oh wait, didn't they just tell me that the board is no longer available. This VCR is now toast, I have no more video, no more beloved tapes I can play, and it ends up being a boat anchor, thanks to Hitachi's stupidity. I forgot to mention this in my original post, but the VCR is not actually working. There are vertical invisible white bars and fuzzy marks all over on the screen (no, it is not the video head), and sometimes it is hard to see the text. I suspect the problem is at the video board. Does anyone know if the VJT700 used any surface-mount caps? I don't know about the VJT700, but I know for sure that VGT650 (Panasonic PV-1780 equivalent) does not use any surface-mount caps. Please help me choose my VCR. I don't want to throw out my CTC-121 just because I can't find the proper, matching VCR for this TV. I was born in 1984, so the TV has to be made in 1984, and no other year can be considered. Originally, I wanted a Panasonic 27" stereo to match with my PV-1730 VCR, but the TV has pretty much been vanished in people's home today and is impossible to find one used. Next I considered was a Sharp 25" stereo Linytron to match with my VC-489U VCR, but it's like Panasonic similar and has already been vanished. Next I looked at Hitachi, but neither the TV nor VCR still exists in people's home today. VCR is VT-88A, and you don't know how many times I get the same e-mail from sellers, "Sorry, I threw it out a long time ago because it broke. I only have the remote and manual left." Then I looked at Mitsubishi, and I was able to find one, but I passed because I was told by Frank in Studio Sound electronics (diyvcrparts.com) that their 1984 VCRs were super bad and buggy. Then I looked at Zenith, but JVC didn't make a 4-head Hi-Fi VCR for Zenith, and one of the idler tires is no longer available, according to Frank. Finally, I ended up with this RCA TV and bought it home happily assuming that 1984 Hitachi VCRs were built like a tank and can run forever. Surprisingly, it does not apply to the VKT650. I didn't look at NEC, Sanyo, Sony, and Toshiba because they only made Beta VCRs. |
|
#3
|
||||
|
||||
|
Quote:
In regards to your question about which VCR, you're not dealing with NEW ONES you can compare in a dealer's showroom anymore. Within your own criteria of '80's-built units you're dealing with what's available NOW that still works. I'd use the one that worked the best no matter WHO it was made by. Make sure it records tapes that can be played back on several other VCR's so that you know it's not recording "out of spec". In other words tapes made on one machine should play back on a handful of other machines with the tracking control set in about the mid position. Hitachi and Panasonic each had their own ideas about "standards". Walt- nothing "runs forever". If you are counting on this you will be sadly disappointed. I'd take what you get that's running right now, take care of it and be ready for disappointment at any time. You talk down about the '90's but keep in mind anything built in the '80's is just "cheaply made" relative to the SEVENTIES. "Cheaply made" and how well it lasts are two different things! Why can you no longer playback tapes because one VCR no longer functions? Was the tape recorded so far out of spec that the out-of-spec machine is the only one that will play it properly? If so, an alignment is in order- don't record anymore "out of spec" tapes until it is repaired. In regards to the lines in your playback picture there were a few models of VCR's made in that time frame that used head switching relays instead of the more RELIABLE IC (sorry- just had to poke you a little). I'm thinking relays were more common in the portables but the upper end table models utilized them, also. The contacts on the relay would get dirty and introduce snow/lines into the playback. I am going from memory and have only serviced a few machines with this problem- I longer have my annotated service data. Try tapping lightly on the relay (should be located close to the video heads and MAY have a clear plastic cover) and see if your lines come and go. For American TV's and Japanese VCR's I don't if there are many models I would say "matched". All should be compatable with each other if they are aligned and functioning properly. Don't try to judge the quality of something based on the year it was made. If you're looking for "visually matching", well, call a decorator! Love your 121 and give that old lady the respect and care she deserves, my friend! Best,Brian |
|
#4
|
|||
|
|||
|
Please pardon my post above, but I didn't mean to say I need a VCR that runs forever, and nothing runs forever. I am determinating the two brands, Panasonic or Hitachi, based on parts availability right now, internal design, video head durability, etc. Without surface-mount caps, I am better off. With surface-mount caps, I am worse off.
|
|
#5
|
||||
|
||||
|
Don't know about parts, but back in their day I had a VFT456 "industrial grade" VCR. Had a 3 prong power cord, and silver instead of wood grain trim. Made a sharper image than the Hitachi's RCA re-labeled later on.
__________________
|
| Audiokarma |
|
#6
|
||||
|
||||
|
Quote:
![]() (Actually, that was a nuke reactor up there, Sarnoff Labs pops up in the NRC/EPA/DOE records because they were somehow involved with the effort, I think leasing lab space or such. I only know about this because I noticed the dead-ringer 'sphere next to a building and cooling towers' on the flight home from Puerto Rico, and looked it up.) |
![]() |
| Thread Tools | |
| Display Modes | |
|
|