Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 04-27-2023, 03:06 PM
timmy's Avatar
timmy timmy is offline
VideoKarma Member
 
Join Date: Jan 2011
Location: Delaware ny
Posts: 3,719
There are I believe capacitors wired to one side of the heaters in the IF strip they are missing and 240pf micas are in place I have no clue if they are right or not or the value that should be there because the schematic don’t show these caps
Reply With Quote
  #2  
Old 04-27-2023, 04:04 PM
bandersen's Avatar
bandersen bandersen is offline
RCA 741PCS
 
Join Date: Mar 2009
Location: Chicago, IL
Posts: 8,829
There are four 250 pF caps on the IF tube heaters. They are shown on the schematic in the filament string section. The values are not critical to the TVs operation. They just filter RF noise off the heater supply.
__________________
Here are my Vintage Radio & TV YouTube Channel and Photo Gallery

Last edited by bandersen; 04-27-2023 at 06:42 PM.
Reply With Quote
  #3  
Old 04-27-2023, 04:26 PM
timmy's Avatar
timmy timmy is offline
VideoKarma Member
 
Join Date: Jan 2011
Location: Delaware ny
Posts: 3,719
Quote:
Originally Posted by bandersen View Post
I'm restoring a TS-4J right now and B+ is only 90 volts but the set works fine.
B+ is derived from 6 tubes acting as a voltage divider.
Quote:
Originally Posted by bandersen View Post
There are four 250 pF caps on the IF tube heaters. They are shown on the schematic in the filament string section. The values are critical to the TVs operation. They just filter RF noise off the heater supply.
There is 240pf mica caps in place should these be ok?
Reply With Quote
  #4  
Old 04-27-2023, 06:43 PM
bandersen's Avatar
bandersen bandersen is offline
RCA 741PCS
 
Join Date: Mar 2009
Location: Chicago, IL
Posts: 8,829
Yes, sorry I meant NOT critical. Mica is overkill for that matter. Any cheapo ceramic disc cap would be fine.
__________________
Here are my Vintage Radio & TV YouTube Channel and Photo Gallery
Reply With Quote
  #5  
Old 04-27-2023, 07:21 PM
timmy's Avatar
timmy timmy is offline
VideoKarma Member
 
Join Date: Jan 2011
Location: Delaware ny
Posts: 3,719
Unless I’m just nuts but the schematic shows there is v10AB v11AB v18AB but where exactly is the clipper shows v10 but both 18 and 11 is being used for audio and oscillator and afc and osc.
Reply With Quote
Audiokarma
  #6  
Old 04-27-2023, 07:41 PM
timmy's Avatar
timmy timmy is offline
VideoKarma Member
 
Join Date: Jan 2011
Location: Delaware ny
Posts: 3,719
I’m just rambling this simple set suddenly is alittle above simple LMAO.
Reply With Quote
  #7  
Old 04-27-2023, 07:49 PM
Chris K Chris K is offline
VideoKarma Member
 
Join Date: Jun 2022
Posts: 1,534
Quote:
Originally Posted by timmy View Post
I’m just rambling this simple set suddenly is alittle above simple LMAO.
No wonder this clumsy novice had no luck with it. Most of the vintage sets I’ve restored needed parts replaced rather than intense analysis. When I did need help I found it here and I was often successful but with this Motorola I obviously was in way over my head!
Reply With Quote
  #8  
Old 04-27-2023, 07:59 PM
bandersen's Avatar
bandersen bandersen is offline
RCA 741PCS
 
Join Date: Mar 2009
Location: Chicago, IL
Posts: 8,829
Yes, V10 sections A & B are the clipper. Not sure where the confusion is? There really shouldn't be any need for intense analysis.
__________________
Here are my Vintage Radio & TV YouTube Channel and Photo Gallery

Last edited by bandersen; 04-27-2023 at 08:02 PM.
Reply With Quote
  #9  
Old 04-28-2023, 04:56 AM
timmy's Avatar
timmy timmy is offline
VideoKarma Member
 
Join Date: Jan 2011
Location: Delaware ny
Posts: 3,719
I think I’m getting screwed up here because I have a voltage chart that I don’t think is the right one for this ts-4h does anyone have the correct voltages for v10 clipper. I only have the schematic no tube location and most numbers are blurry and can’t make out what is what.

Last edited by timmy; 04-28-2023 at 05:56 AM.
Reply With Quote
  #10  
Old 04-28-2023, 07:33 AM
Yamamaya42's Avatar
Yamamaya42 Yamamaya42 is offline
VideoKarma Member
 
Join Date: Nov 2018
Location: Round Rock TX
Posts: 3,254
The voltages shown in the SAMS should be rather close in all versions, not sure why so much focus is being drawn to this clip circuit, it's most likely OK, the circuits tied to it (v11) , transformers ETC, almost look like a horizontal blocking oscillator setup, and if there is raster, it must be running.
__________________
=^-^=
Yasashii yoru ni hitori utau uta. Asu wa kimi to utaou. Yume no tsubasa ni notte.
いとおしい人のために
Reply With Quote
Audiokarma
  #11  
Old 04-28-2023, 07:51 AM
Yamamaya42's Avatar
Yamamaya42 Yamamaya42 is offline
VideoKarma Member
 
Join Date: Nov 2018
Location: Round Rock TX
Posts: 3,254
OK, so I guess the better name for this “clipper” would be sync separator.
But as seen in Bob's YT videos before, the GIGO principal has major impact here, if the received video is not up to par, too high/low or distorted in some way, the sync sep won't have clean info to pass through to the sweep circuits, thus you get unstable video lock.
__________________
=^-^=
Yasashii yoru ni hitori utau uta. Asu wa kimi to utaou. Yume no tsubasa ni notte.
いとおしい人のために
Reply With Quote
  #12  
Old 04-28-2023, 07:56 AM
timmy's Avatar
timmy timmy is offline
VideoKarma Member
 
Join Date: Jan 2011
Location: Delaware ny
Posts: 3,719
Vertical is affected and looks like horizontal lines as well it looks like it’s trying to tear but can see a nice clear picture in between the tearing I thought maybe it was overloading at the video level but not sure as yet I have something else I’m going for.
Reply With Quote
  #13  
Old 04-28-2023, 10:03 AM
timmy's Avatar
timmy timmy is offline
VideoKarma Member
 
Join Date: Jan 2011
Location: Delaware ny
Posts: 3,719
If the video signal is overloading to much for the sync to work then ok possible but from what I understand the slug on the detector was turned maybe this would cause this not sure.
Reply With Quote
  #14  
Old 04-28-2023, 12:58 PM
Yamamaya42's Avatar
Yamamaya42 Yamamaya42 is offline
VideoKarma Member
 
Join Date: Nov 2018
Location: Round Rock TX
Posts: 3,254
I'm just going on speculation here, never having worked on a electrostatic type set myself yet, but assuming that bias power and video is clean, winch really can't be done with the naked eye from a troubleshooting standpoint, but if so, you would have to go over every inch of the sync separator circuit (or as it's called, clipper here.) from where it's taken off the video amp circuit to where it's processed, and fed to the horizontal / vertical OSCs, making sure that all in between is correct and in tolerance.
__________________
=^-^=
Yasashii yoru ni hitori utau uta. Asu wa kimi to utaou. Yume no tsubasa ni notte.
いとおしい人のために
Reply With Quote
  #15  
Old 04-28-2023, 01:43 PM
timmy's Avatar
timmy timmy is offline
VideoKarma Member
 
Join Date: Jan 2011
Location: Delaware ny
Posts: 3,719
Got a perfect picture now however when it warms up the vertical size collapses and gets jittery and lines across mostly the bottom and some on top. I tried the retrace mod and it gets rid of slot of lines but the size problem is still there.
Reply With Quote
Audiokarma
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:11 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.