Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 08-04-2020, 10:54 AM
Yamamaya42's Avatar
Yamamaya42 Yamamaya42 is offline
VideoKarma Member
 
Join Date: Nov 2018
Location: Round Rock TX
Posts: 3,254
Quote:
Originally Posted by Electronic M View Post
My policy on anything pre 1960 is to look up all domino caps on the schematic and replace all rated at 1000pF higher. 1000pF is the threshold where dominos go from usually mica dielectric to usually paper dielectric. The paper dominos also usually have a white dot on them...If there's not a 9 in the capacitance and the capacitance is close to the paper cap range I also consider changing caps.
I've seen blown micamold paper line bypass caps that blew before my ownership before... always a mess.

Watching Card Captor Sakura I see.
Well, I started to run out of LD movies to play while testing, so I went to my original stock of CCS LDs .
And, DO have them all, as I fansubbed the entire series in the 90s
__________________
=^-^=
Yasashii yoru ni hitori utau uta. Asu wa kimi to utaou. Yume no tsubasa ni notte.
いとおしい人のために
Reply With Quote
  #2  
Old 08-12-2020, 07:27 AM
Yamamaya42's Avatar
Yamamaya42 Yamamaya42 is offline
VideoKarma Member
 
Join Date: Nov 2018
Location: Round Rock TX
Posts: 3,254
I found a " Dunsel "

An old Blonder Tongue Ultraverter Dunsel to be exact!
https://www.ebay.com/itm/20151173538...m=201511735381

Obviously, it can never be used for anything even if it ever works again, but it's just too unique not to have!
__________________
=^-^=
Yasashii yoru ni hitori utau uta. Asu wa kimi to utaou. Yume no tsubasa ni notte.
いとおしい人のために
Reply With Quote
  #3  
Old 08-12-2020, 04:07 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
Quote:
Originally Posted by Yamamaya42 View Post
I found a " Dunsel "

An old Blonder Tongue Ultraverter Dunsel to be exact!
https://www.ebay.com/itm/20151173538...m=201511735381
We sold a gadzillion of those back in the day. Biggest problem with 'em was intermittency of the wipers on the tuning rings. Cleaning and re-lubing usually helped. Used a 6AF4 and 6AB4. The one tube version had just the 6AF4. Don't recall ever replacing a tube.
Reply With Quote
  #4  
Old 08-12-2020, 10:15 AM
old_tv_nut's Avatar
old_tv_nut old_tv_nut is offline
See yourself on Color TV!
 
Join Date: Jul 2004
Location: Rancho Sahuarita
Posts: 7,815
Well, just for grins and giggles, you could use it to convert a digital UHF to VHF and then receive it with a digital receiver or converter box.
__________________
www.bretl.com
Old TV literature, New York World's Fair, and other miscellany
Reply With Quote
  #5  
Old 08-12-2020, 10:45 AM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
If it is still working and you have an agile modulator transmitting at UHF you could hook it to your 630 clone or your Setchell (or was it Stromberg? ) Carlson.

I have a few of that things cousins near my work bench. I forget if their gutted or not...I've got roughly 4-6 UHF converter and or VHF antenna amps and 1-2 or the ones I bought were gutted by their previous radio collector owners... one day I'm going either built an AM transmitter in or a clone of a vintage tube RF modulator I bought from the ETF a few years ago.
Attached Images
File Type: jpg IMG_20200812_103118761.jpg (43.5 KB, 16 views)
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4

Last edited by Electronic M; 08-12-2020 at 10:51 AM.
Reply With Quote
Audiokarma
  #6  
Old 08-12-2020, 03:24 PM
dtvmcdonald's Avatar
dtvmcdonald dtvmcdonald is offline
VideoKarma Member
 
Join Date: Nov 2012
Posts: 1,268
Quote:
Originally Posted by Electronic M View Post
If it is still working and you have an agile modulator transmitting at UHF you could hook it to your 630 clone or your Setchell (or was it Stromberg? ) Carlson.
Convert it to output on Ch. 1 and feed it to your pre-war TV.
Reply With Quote
  #7  
Old 08-12-2020, 03:37 PM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
Quote:
Originally Posted by dtvmcdonald View Post
Convert it to output on Ch. 1 and feed it to your pre-war TV.
Pretty sure neither I or the OP have a Pre-war TV. I'd like own one some day but given they tend to go for classic car money and I'd rather have a classic car for the money it will probably be a while before I own one.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
  #8  
Old 08-12-2020, 05:28 PM
dtvmcdonald's Avatar
dtvmcdonald dtvmcdonald is offline
VideoKarma Member
 
Join Date: Nov 2012
Posts: 1,268
Quote:
Originally Posted by Electronic M View Post
Pretty sure neither I or the OP have a Pre-war TV. I'd like own one some day but given they tend to go for classic car money and I'd rather have a classic car for the money it will probably be a while before I own one.
I meant to say "early post-war".

You can afford lots of Hallicrafters T54s with Ch. 1. They make good pictures:
Hint for them: buy a cheap 4" 230 volt AC fan and put it on the RF coil ...
it works nicely on 122 volts and is quiet as a whisper.

I assure you however that pre-war US TVs can be had for reasonable prices
if you are willing to settle for a TRK120. You're thinking British.
Reply With Quote
  #9  
Old 08-19-2020, 12:47 PM
Jon1967us Jon1967us is offline
VideoKarma Member
 
Join Date: Nov 2018
Posts: 350
Is the point that there's no or much less interference on UHF, if you use that to transmit in the house, vs VHF?

Quote:
Originally Posted by Electronic M View Post
If it is still working and you have an agile modulator transmitting at UHF you could hook it to your 630 clone or your Setchell (or was it Stromberg? ) Carlson.

I have a few of that things cousins near my work bench. I forget if their gutted or not...I've got roughly 4-6 UHF converter and or VHF antenna amps and 1-2 or the ones I bought were gutted by their previous radio collector owners... one day I'm going either built an AM transmitter in or a clone of a vintage tube RF modulator I bought from the ETF a few years ago.
Reply With Quote
  #10  
Old 08-19-2020, 01:56 PM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
Quote:
Originally Posted by Jon1967us View Post
Is the point that there's no or much less interference on UHF, if you use that to transmit in the house, vs VHF?
Nope. My point was they had an antique UHF converter designed to add UHF to older sets that didn't come with UHF when new, and they could still use it if they transmitted UHF.
Interference varies from place to place depending on a number of factors. UHF could be better or worse depending on where you are, what UHF DTV channels are transmitting* in your area, what type of noise is produced by the switch mode supplies you and your neighbors are using, atmospheric noise, etc.

My advice to anyone planning to transmit their own low power analog is start with an agile (agile meaning you can change which channel it transmitts on) modulator, a DTV converter box with signal strength and manual RF channel selection in the menus, and an analog TV.
*You don't want to transmit on a channel that a local DTV station is using as you'll interfere with each other (the UHF band tends to be more packed with transmitters, but ATSC 3 is changing that). I typically use my Zenith DTV converter boxes to figure out which channels have active DTV stations and avoid those channels (I need to get an ATSC 3 capable box to check for those signals too). The static on an analog TV can tell you a bit about what noise exists on what channels too...once you have an idea where other transmitters and noise exists pick something that has the least of that, set your transmitter to one of those promising channels and try it out...If it sucks try a different channel.

IMO The fixed channel modulators are something you get after you've tried a channel with the agile modulator and know it's good... Otherwise you risk undiscovered interference making the fixed channel modulator as useful as a door stop.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4

Last edited by Electronic M; 08-19-2020 at 02:00 PM.
Reply With Quote
Audiokarma
  #11  
Old 08-12-2020, 07:28 PM
Yamamaya42's Avatar
Yamamaya42 Yamamaya42 is offline
VideoKarma Member
 
Join Date: Nov 2018
Location: Round Rock TX
Posts: 3,254
Right now, my FADA is still in direct A/V input mode, as I had trouble with doing the IF alignment procedure, tried more than once, where as the tuner DOES work, there is heavy RFI on channel 3, which is seen to a lesser degree on 4, and adding a rf amp helped even more, it did not make it go away completely, but when I did get a BT modulator for chan 7, I did find it free from RFI, but the tuner has contact problems on THAT channel

The instructions clearly says set to channel 9 when doing IF alignment on this set, but someone said that any chan can be used ( this is also reflected in later instructions for other sets ) , since the osc tube is removed and the signal fed in the aunt input.
For example, I just ordered a BT modulator for chan 11, if I can confirm that 11 works OK w/o any problems. Can't I use 11 in the alignment procedure where it says to use 9? will it make any difference?
https://i.imgur.com/HpMK2wJ.jpg

But then what to do with the BT mod chan 7? use it on my CTC-16XL? :p

interesting idea.
But it too has minor IF problems, that I don not have the equipment to adjust,
nothing really THAT bad, just red bleeding that will move with the fine tuning, perhaps I will try to fix SOME day!

But for the stromberg carlson x-21 , I do like the idea of feeding it UHF and having the ultraverter convert for it! I just have to be sure to find a modulator that IS uhf and not CATV . :p
__________________
=^-^=
Yasashii yoru ni hitori utau uta. Asu wa kimi to utaou. Yume no tsubasa ni notte.
いとおしい人のために
Reply With Quote
  #12  
Old 08-12-2020, 08:38 PM
Tom9589 Tom9589 is offline
VideoKarma Member
 
Join Date: Jan 2013
Location: Stone Mountain, GA
Posts: 492
Many moons ago, I had a Philco UHF up converter. I used it with my 1076 B&K TV Analyst which only had VHF coverage. Set the 1076 to channel 4 and hook up the Philco and you had channels 14-83 at your fingertips. When I got a 1077, I got rid of the Philco.

I particularly remember the precision vernier for setting the UHF channels. It even had a hand typewritten scale which told you the exact setting for each channel.
Reply With Quote
  #13  
Old 08-13-2020, 09:57 AM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
Quote:
Originally Posted by Tom9589 View Post
Many moons ago, I had a Philco UHF up converter. I used it with my 1076 B&K TV Analyst which only had VHF coverage. Set the 1076 to channel 4 and hook up the Philco and you had channels 14-83 at your fingertips. When I got a 1077, I got rid of the Philco.

I particularly remember the precision vernier for setting the UHF channels. It even had a hand typewritten scale which told you the exact setting for each channel.
So you fed the CH4 output of the B&K into the output of the UHF converter and the converter worked backwards and spit UHF out of it's input?....I never thought of that but the principal seems sound. This gives me some fascinating ideas for UHF agile modulator add-ons to my existing VHF modulators.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
  #14  
Old 08-13-2020, 02:00 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by Electronic M View Post
So you fed the CH4 output of the B&K into the output of the UHF converter and the converter worked backwards and spit UHF out of it's input?....I never thought of that but the principal seems sound. This gives me some fascinating ideas for UHF agile modulator add-ons to my existing VHF modulators.
I think you may be overthinking this. More likely used the 1076 as a VHF signal source into the UHF converter, in order to make the 1076 signal usable on UHF tuner TV's. I can't imagine what else what would have been going on.
Reply With Quote
  #15  
Old 08-13-2020, 11:55 AM
bandersen's Avatar
bandersen bandersen is offline
RCA 741PCS
 
Join Date: Mar 2009
Location: Chicago, IL
Posts: 8,829
Quote:
Originally Posted by Tom9589 View Post
Many moons ago, I had a Philco UHF up converter. I used it with my 1076 B&K TV Analyst which only had VHF coverage. Set the 1076 to channel 4 and hook up the Philco and you had channels 14-83 at your fingertips. When I got a 1077, I got rid of the Philco.

I particularly remember the precision vernier for setting the UHF channels. It even had a hand typewritten scale which told you the exact setting for each channel.
I believe that would be the Philco G-8000. They show up for sale now and then.

https://worldradiohistory.com/hd2/ID...-Page-0021.pdf

__________________
Here are my Vintage Radio & TV YouTube Channel and Photo Gallery
Reply With Quote
Audiokarma
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:37 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.