![]() |
|
|
|
#1
|
||||
|
||||
|
Sencore VA48 TV analyzer
I picked up this Sencore VA48 TV analyzer on ebay a few months ago. It combines a pattern generator, tuner sub, various drive signals for tube and SS sets, flyback and yoke tester, etc. Everything appears to be working. There is a small quick set up book in the rear compartment; but, I don't have the main manual. I think I've got around $40 including shipping in it. A friend had a newer Sencore outfit that I think he had about $10K in. Has anyone had any experience with this piece of equipment and is this a good choice for vintage TV repair?
|
|
#2
|
||||
|
||||
|
I have one of those as well, and I have the complete manual, I think. I bought mine and tuned it up several years ago, and now it has sat again for a while. Yes, it should have many uses in restoring antique TV sets, though I have never put mine to much use (I just got more involved in my old TV sets again after not doing much for years). I will look at mine in the next few days, and I will see what documents I have.
__________________
Chris Quote from another forum: "(Antique TV collecting) always seemed to me to be a fringe hobby that only weirdos did." |
|
#3
|
||||
|
||||
|
I also need to get some probes for mine. I'll admit that I've only used a multimeter and a scope to fix most things; but, the price seemed right on this piece. Most cheap modern TV's have about gotten to the point where if it can't be fixed with a multimeter; then, they aren't worth fixing. I also have an older stand alone Sencore flyback and yoke tester that will also check HV (if I had the probe). I've used it some on some newer flybacks with pretty good results.
|
|
#4
|
||||
|
||||
|
I have one too. It comes in handy for subbing things like the tuner output to see if you have noise from your tuner, or if it's coming from downstream, and you can inject horizontal drive, vertical pulses, etc etc. It also has a color bar generator. Again, I don't use it often at all, but I like having it. I've never used the FBT and yoke ringer. I have a much newer Sencore LC-101 for that (and for full-working voltage cap leakage testing
)Charles
__________________
Collecting & restoring TVs in Los Angeles since age 10 |
|
#5
|
||||
|
||||
|
Quote:
I bought about 300 FP (can) caps from a company on eBay and sat for 3 nights checking them on my LC102. I found 3 that were bad - all 3 for dielectric absorption and 1 of the 3 also had bad ESR on two of the four sections. My only complaint is the keypad - I got bruised finger tips from holding the buttons down for some tests. I wish ESR was a no-hands test. For troubleshooting, I'll use my Bob Parker/Dick Smith ESR meter. Cheers,
__________________
Brian USN RET 22YRS (Avionics/Cal) CET-Consumer Repair and Avionics ('88) "Capacitor Cosmetologist since '79" When fuses go to work, they quit! |
| Audiokarma |
|
#6
|
|||
|
|||
|
This is an excellent piece of equipment for servicing older TV's.
__________________
julian |
|
#7
|
||||
|
||||
|
I have an ESR meter that I use for quickly spotting dry electrolytics in newer equipment, but I haven't used it on cans in old TVs.
On the LC101, there's a goofy little spring rod thing that you put between the handle and the buttons for long-time forming. I couldn't believe that's what it was for, but it's in the book!!! Does the 102 also have it? I've never used it myself because I'd be afraid I'd forget, and that might result in a loud BANG!, and oily black capaci-fuzz all over the house. Charles
__________________
Collecting & restoring TVs in Los Angeles since age 10 |
|
#8
|
||||
|
||||
|
Quote:
Cheers
__________________
Brian USN RET 22YRS (Avionics/Cal) CET-Consumer Repair and Avionics ('88) "Capacitor Cosmetologist since '79" When fuses go to work, they quit! |
|
#9
|
||||
|
||||
|
Ok, I've got a VA48. It's a bit low on functionality because some circuit board under the main chassis has gone *poof*.
Anyone got a schematic on one of these things? |
|
#10
|
|||
|
|||
|
I recently got this unit. Did anyone ever find or upload a main manual?
|
| Audiokarma |
|
#11
|
|||
|
|||
|
Quote:
|
|
#12
|
||||
|
||||
|
Quote:
Of course, you'd have to ask nicely, as Rich once had trouble getting an overlay for HIS company-issued LC53 - long story, but do not clean the vinyl overlays with nail-polish remover! Sencore gave him the run-around, and soon after he left the company, and went to work for RCA, later GE/RCA, as a service seminar host for several states.
__________________
Brian USN RET 22YRS (Avionics/Cal) CET-Consumer Repair and Avionics ('88) "Capacitor Cosmetologist since '79" When fuses go to work, they quit! |
|
#13
|
||||
|
||||
|
Guys,
Second manual posted to same url/directory I PM'd you. It was easier to scan than I thought.... Hope it helps. Cheers,
__________________
Brian USN RET 22YRS (Avionics/Cal) CET-Consumer Repair and Avionics ('88) "Capacitor Cosmetologist since '79" When fuses go to work, they quit! |
|
#14
|
||||
|
||||
|
i would like a copy also i can give you a donation. thanks steve
|
|
#15
|
||||
|
||||
|
We had 3 VA48's at one time. IIRC they came with a quick guide
& an extensive manual that was VERY useful. Only problems with them was the coax output would get loose & a special diode behind it would break. Also they had harmonica connectors that would go cold. Sencor ran a great sales seminar. Always learned from it. Twas a great machine to work with. 73 Zeno
|
| Audiokarma |
![]() |
| Thread Tools | |
| Display Modes | |
|
|