Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Solid State CRT Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 01-30-2026, 01:09 PM
vol.2's Avatar
vol.2 vol.2 is offline
VideoKarma Member
 
Join Date: Feb 2023
Posts: 435
Quote:
Originally Posted by TinCanAlley View Post
I think I'll check the single capacitor on it and then install it.
You might want to do a quick check on the resistors while you are at it.

Generally speaking, the resistors should be their value or lower when in circuit because any additional paths that they might follow in parallel to their position in the circuit will only bring the total resistance down, not up.

So if you check a resistor and it is either open or it's resistance is higher than the value on the case, you should remove one leg from the circuit and give it a real test.

It's also a good idea to (if possible) identify places in the circuit where there should be ground (zero volts) and a power rail, and make sure those places are not a short.
Reply With Quote
  #2  
Old 01-30-2026, 06:02 PM
TinCanAlley's Avatar
TinCanAlley TinCanAlley is offline
VideoKarma Member
 
Join Date: Sep 2008
Location: So Cal, CA
Posts: 1,026
Quote:
Originally Posted by vol.2 View Post
You might want to do a quick check on the resistors while you are at it.

Generally speaking, the resistors should be their value or lower when in circuit because any additional paths that they might follow in parallel to their position in the circuit will only bring the total resistance down, not up.

So if you check a resistor and it is either open or it's resistance is higher than the value on the case, you should remove one leg from the circuit and give it a real test.

It's also a good idea to (if possible) identify places in the circuit where there should be ground (zero volts) and a power rail, and make sure those places are not a short.
I can do that.

Any idea which board could alter tint? I see it on the schematic at the subcarrier and going to the chroma. Is it the subcarrier altering or is the chroma also able to alter it if something is wrong on the board?

I think I'm also going to pull each board, deoxit all the contacts on chassis and boards. I also noticed that when I look at pics of the chassis when I first got it, each board had 2 blue tubes on unused pins. No doubt used to secure the boards, but are these a real necessity or more for shipping? I really can't remember where I put them as I didn't put them back on the modules.
__________________
Pioneer SX-1080, Pioneer PL-115D, Pioneer CT-F9191, Pioneer RG-1, Wollensak 8050A, Akai 4000DS MkII, Pioneer CS-05 & Polk 1.2TL

Denon 5803A, Pioneer DVL-700, Pioneer CT-W603RS, Toshiba HD-A3, D-Link DSM-520, Dish VIP-722, Polk 1.2TL, CSi5, LS/fx, RT-800 and PSW-650
Reply With Quote
  #3  
Old 01-30-2026, 07:34 PM
vol.2's Avatar
vol.2 vol.2 is offline
VideoKarma Member
 
Join Date: Feb 2023
Posts: 435
Quote:
Originally Posted by TinCanAlley View Post
I can do that.

Any idea which board could alter tint? I see it on the schematic at the subcarrier and going to the chroma. Is it the subcarrier altering or is the chroma also able to alter it if something is wrong on the board?

I think I'm also going to pull each board, deoxit all the contacts on chassis and boards. I also noticed that when I look at pics of the chassis when I first got it, each board had 2 blue tubes on unused pins. No doubt used to secure the boards, but are these a real necessity or more for shipping? I really can't remember where I put them as I didn't put them back on the modules.
Again, I'm not really that familiar with these sets to the point I can offer a lot of specific advice on them.

Someone else will have to comment on which board does what.

I definitely agree with the idea of cleaning board edge contacts though. That can solve a lot of problems.

A related thing to check is the solder joints on any connectors that get stress. If you have edge contacts that slide into connectors, those connectors will be prone to cracked solder joints, and that is a common cause of intermittent issues because they can make good contact until they heat up, and then the heat causes things to warp and push apart and issues start to show up.

It's not a slam-dunk, but it is a common kind of fault and worth just reflowing.

If I'm working on an old set (regardless of the make), I will generally do three things before I bother even turning on. I check and replace any bad electrolytics, I use contact cleaner and fader lube on every contact, switch, pot, fader, jack on the set, and I reflow every single connector, socket or large heavy component (like a transformer) on the PCB.

My time is too valuable to chase my tail over a cracked solder joint if you know what I mean.
Reply With Quote
  #4  
Old 01-31-2026, 04:07 PM
TinCanAlley's Avatar
TinCanAlley TinCanAlley is offline
VideoKarma Member
 
Join Date: Sep 2008
Location: So Cal, CA
Posts: 1,026
Quote:
Originally Posted by vol.2 View Post
Again, I'm not really that familiar with these sets to the point I can offer a lot of specific advice on them.

Someone else will have to comment on which board does what.

I definitely agree with the idea of cleaning board edge contacts though. That can solve a lot of problems.

A related thing to check is the solder joints on any connectors that get stress. If you have edge contacts that slide into connectors, those connectors will be prone to cracked solder joints, and that is a common cause of intermittent issues because they can make good contact until they heat up, and then the heat causes things to warp and push apart and issues start to show up.

It's not a slam-dunk, but it is a common kind of fault and worth just reflowing.

If I'm working on an old set (regardless of the make), I will generally do three things before I bother even turning on. I check and replace any bad electrolytics, I use contact cleaner and fader lube on every contact, switch, pot, fader, jack on the set, and I reflow every single connector, socket or large heavy component (like a transformer) on the PCB.

My time is too valuable to chase my tail over a cracked solder joint if you know what I mean.
I'm going to remove all the boards and clean all contacts and reseat. Will also check all components on the boards that handle color. The schematics show the tint control connected to the subcarrier, but if the correct setting hits that board and is then sent to the chroma board, it could change if that board has issues.
__________________
Pioneer SX-1080, Pioneer PL-115D, Pioneer CT-F9191, Pioneer RG-1, Wollensak 8050A, Akai 4000DS MkII, Pioneer CS-05 & Polk 1.2TL

Denon 5803A, Pioneer DVL-700, Pioneer CT-W603RS, Toshiba HD-A3, D-Link DSM-520, Dish VIP-722, Polk 1.2TL, CSi5, LS/fx, RT-800 and PSW-650
Reply With Quote
  #5  
Old 03-13-2026, 10:06 AM
TinCanAlley's Avatar
TinCanAlley TinCanAlley is offline
VideoKarma Member
 
Join Date: Sep 2008
Location: So Cal, CA
Posts: 1,026
Been awhile since I posted an update and possible question or two.

I managed to get my hands on a new IC for the chroma board and just got some 16pin sockets. I'm going to remove the individual pin sockets on the board and replace with a single unit and put the new IC in. I'm leaning toward all my tint issues being this board. The tint is done by the subcarrier by changing the phase of the burst which then goes to the chroma board. At first I thought the subcarrier, but now I get sudden burst of fully saturated color as if I turned up the color control to max. It can last anywhere from 1 second to almost a minute. Yesterday during a couple of hours of viewing, it did it 9 times and the tint wandered a bit, but nothing extremely noticeable. Since the burst with tint phase hits that board, and the color is done on that board, it is most likely on that board. The IC handles both of those, so if it's faulty, changing it is my next step in troubleshooting.

And of course I have a question. I've noticed recently that on images with red or orange, there is a ghosting of that color to the left of the image. For instance, a person was wearing red suspenders and to the left of the suspenders, there was a lighter transparent red on his shirt leading to the suspenders. I also noticed the same with someone wearing orange. No other color does this. Might by related to the issues I'm having with tint and color saturation. All searches I've come up with point to a capacitor, but I've replaced all the electrolytics. Guess one could be bad already.

If you want an pic, I can take one and post it.
__________________
Pioneer SX-1080, Pioneer PL-115D, Pioneer CT-F9191, Pioneer RG-1, Wollensak 8050A, Akai 4000DS MkII, Pioneer CS-05 & Polk 1.2TL

Denon 5803A, Pioneer DVL-700, Pioneer CT-W603RS, Toshiba HD-A3, D-Link DSM-520, Dish VIP-722, Polk 1.2TL, CSi5, LS/fx, RT-800 and PSW-650
Reply With Quote
Audiokarma
  #6  
Old 03-13-2026, 05:58 PM
TinCanAlley's Avatar
TinCanAlley TinCanAlley is offline
VideoKarma Member
 
Join Date: Sep 2008
Location: So Cal, CA
Posts: 1,026
Finished modifying and installing the new IC on the Chroma board. Will have to run it through its paces and see if it helps. I think it already has as the tint was off from how it was before the new IC and it adjusted as expected.
Attached Images
File Type: jpg Chroma IC Socket 1.jpg (95.3 KB, 8 views)
File Type: jpg Chroma IC Socket 2.jpg (95.7 KB, 7 views)
File Type: jpg Chroma IC Socket 3.jpg (98.3 KB, 7 views)
__________________
Pioneer SX-1080, Pioneer PL-115D, Pioneer CT-F9191, Pioneer RG-1, Wollensak 8050A, Akai 4000DS MkII, Pioneer CS-05 & Polk 1.2TL

Denon 5803A, Pioneer DVL-700, Pioneer CT-W603RS, Toshiba HD-A3, D-Link DSM-520, Dish VIP-722, Polk 1.2TL, CSi5, LS/fx, RT-800 and PSW-650
Reply With Quote
  #7  
Old 03-14-2026, 05:50 PM
TinCanAlley's Avatar
TinCanAlley TinCanAlley is offline
VideoKarma Member
 
Join Date: Sep 2008
Location: So Cal, CA
Posts: 1,026
More than 4 hours of testing the new IC and socket and all is well. No tint shifting or color going full saturation. It seem I found the culprit and now can focus on enjoying the set.

I hooked up the Archer Video Distribution System with a VCR, Laserdisc and DVD player connected to it. Each on get switched from their standard channel 3 to separate channels on UHF, so now I can just fire up a device or more and switch the channel to view it. Kind of cool device. Just wish I could get them to broadcast for wireless viewing.
__________________
Pioneer SX-1080, Pioneer PL-115D, Pioneer CT-F9191, Pioneer RG-1, Wollensak 8050A, Akai 4000DS MkII, Pioneer CS-05 & Polk 1.2TL

Denon 5803A, Pioneer DVL-700, Pioneer CT-W603RS, Toshiba HD-A3, D-Link DSM-520, Dish VIP-722, Polk 1.2TL, CSi5, LS/fx, RT-800 and PSW-650
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:43 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.