![]() |
|
|
|
#1
|
|||
|
|||
|
Quote:
|
|
#2
|
||||
|
||||
|
Quote:
You already eliminated the easiest one, which is bad adjustment. That leaves dead components. The by far most likely thing is one or more electrolytics have failed. As you heard from redk in their previous post. The function that controls the parabola is called "EastWest" and is probably denoted in the schematic for your TV as the "EW out" pin on the monolithic video IC. This can be seen at pin 59 on page 22. It joins the deflection circuitry at Q411 on page 23 (towards the upper left side of the page). I would focus on the electrolytics in this section, beneath the vertical output IC. However, I would also heed redk's advice and check the electrolytics in the power supply, and I would also check all of them in anything that gets hot (next to a heat sink or power resistor) or just any of them in the deflection area as those tend to get a lot of juice. This set is an Orion set (not actually made by Toshiba) and it's 2003, which is capacitor plague era. There's every possibility that all the lytics are going to leak or explode unfortunately. |
|
#3
|
|||
|
|||
|
Quote:
I will probably just wind up replacing the capacitors in those areas. There aren't that many. I do notice that the vertical deflection section of the board is a darker brown than the other parts. This TV has a beautiful picture. The tube has a an Orion sticker but it was actually manufactured by Matsushita. 6th gen games look especially amazing on this CRT. |
|
#4
|
||||
|
||||
|
Quote:
Go over any place on the PCB that looks "dark" or different very carefully with new solder and make sure it's all reflowed. Also reflow anything that is big and heavy (like the flyback and big resistors) or connectors (because they get stressed). It's also likely that the caps need to be checked though. Quote:
|
|
#5
|
|||
|
|||
|
Quote:
I also have a Panasonic 27" CRT TV (model CT27D11E, made in 2001) and the tube in that set has the same codes on the label as the Toshiba 27A33. The codes on both tubes are E118951 and LR29056. Another similarity between the tubes is that both tubes have a bold "M" at the top of the label with a square around it. This is the symbol that Matsushita used on their tubes to indicate that they manufactured the tube. This is the symbol I'm referring to, https://deskthority.net/wiki/File:Br...(IE139097).svg. Another piece of information comes from the Union Electronic Distributors website. They have been one of the largest suppliers of consumer electronics parts since the 1950s. The following link shows the tube in the 27A33 (tube # M68LWF088X50) as being manufactured by PANASONIC (MATSUSHITA), (https://www.ued.net/ued/viewItemActi...68LWF088X50Y5P). The picture also looks very similar on each set. I made a post on the CRTgaming subreddit asking about this, http://(https://www.reddit.com/r/crt...icture_tubes/). Last edited by CRTguy; 03-05-2025 at 04:32 PM. |
| Audiokarma |
|
#6
|
||||
|
||||
|
Quote:
In fact, by the time this TV was made, Panasonic had long since already started to farm out the manufacturing of their own devices to Taiwan, Singapore and other places in the Far East. It is entirely possible and would not be weird that the tube is the same tube used by Panasonic in their own sets AND also made by Orion, specifically for Panasonic (thus the "M"). |
|
#7
|
|||
|
|||
|
Quote:
Last edited by CRTguy; 03-05-2025 at 07:22 PM. |
![]() |
| Thread Tools | |
| Display Modes | |
|
|