Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Solid State CRT Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 01-28-2025, 04:50 PM
CRTguy CRTguy is offline
VideoKarma Member
 
Join Date: Feb 2021
Posts: 33
Quote:
Originally Posted by vol.2 View Post
I've encountered sets that were fairly clean inside (but not so clean that they had clearly been washed up) with burned up resistors, etc.

Some TVs just had kind of bad power supply designs.

However, if you're seeing dark spots in the deflection area, that kind of sounds like high hours.

In general, the amount of soot on the flyback and the bell housing of the CRT is a much better indicator of use because the high voltage attracts the soot.

If it's got a lot of soot, and it has dark spots on the boards near big power resistors and the deflection, you are looking at a high hour set.

"Soot" is different that "dust" in that it's very fine and usually black. The high voltage attracts tiny particles in the air and they stick directly to the internal surfaces. The "dust" will just be solid dirt and bunnies inside the thing.

Likewise, if there's a lot of soot and no burn marks, it's also probably high hour. Not all sets had power supplies that burned up the PCBs. Personally, I see that a lot more in sets from the 80s where the part count is started to get reduced, but they don't have the simplified and optimized designs that started to appear in the mid 90s.
How many hours would you consider high hours? Chances are that my Panasonic set is a higher hour set. There was some soot on the tube and on the flyback but not a huge amount. I will say that the picture still looks very good. I always thought it was a low hour set until I took the back up. One other thing is that this TV has 1 composite input on the front and on the top of the PCB where this composite input is, the PCB is black around some of the components. It's not charred by there is a black color. The bottom of the board is not black at all. I'm wondering if the set is still safe to operate if there is a little bit of black on the PCB?
Reply With Quote
  #2  
Old 01-28-2025, 07:38 PM
vol.2's Avatar
vol.2 vol.2 is offline
VideoKarma Member
 
Join Date: Feb 2023
Posts: 435
Quote:
Originally Posted by CRTguy View Post
How many hours would you consider high hours? Chances are that my Panasonic set is a higher hour set. There was some soot on the tube and on the flyback but not a huge amount. I will say that the picture still looks very good. I always thought it was a low hour set until I took the back up. One other thing is that this TV has 1 composite input on the front and on the top of the PCB where this composite input is, the PCB is black around some of the components. It's not charred by there is a black color. The bottom of the board is not black at all. I'm wondering if the set is still safe to operate if there is a little bit of black on the PCB?
I never really though about it tbh, but if you consider that a high hour set could have been used for 10 years, for 3 hours a day, maybe 5 days a week or more, that's 7000-10,000 hours.

One of the older members here that did professional repair work would have a better answer.

Yes, it can be bad or dangerous in some cases to run a TV that has obvious black charring on the PCB. The black stuff is carbon, and carbon is conductive. If there's enough electrical potential on the carbon burn mark, it can cause arcing. I've never had it happen to me, but I've seen videos on YT that showed it happening.

Generally though, mild darkening or discoloration isn't a problem, just actual carbon burn marks or charring. There's stuff you can do to cover it up. When I find areas like that, I typically replace the resistors with something beefier with longer legs and solder them off the PCB a good ways to allow the heat to dissipate better. Not sure if that's the best thing to do, but it makes me feel better.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:24 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.