Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early Color Television

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 09-03-2024, 11:35 PM
old_tv_nut's Avatar
old_tv_nut old_tv_nut is offline
See yourself on Color TV!
 
Join Date: Jul 2004
Location: Rancho Sahuarita
Posts: 7,815
Could you explain a bit more about the vertical capacitor selection? I don't seem to have a significant drift in linearity with warmup, but it's nowhere near perfect either. I'd have to look again, but I think when the top and bottom are symmetrical on average, the very top is pinched a bit, and there is a noticeable transition near the center of the picture that's visible with vertically scrolling titles. Replacing tubes helped, but didn't totally fix it.

My set has developed a brightness drift - too high when first turned on, drifts darker over a minute or two.
__________________
www.bretl.com
Old TV literature, New York World's Fair, and other miscellany
Reply With Quote
  #2  
Old 09-04-2024, 09:13 AM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
Quote:
Originally Posted by old_tv_nut View Post
Could you explain a bit more about the vertical capacitor selection? I don't seem to have a significant drift in linearity with warmup, but it's nowhere near perfect either. I'd have to look again, but I think when the top and bottom are symmetrical on average, the very top is pinched a bit, and there is a noticeable transition near the center of the picture that's visible with vertically scrolling titles. Replacing tubes helped, but didn't totally fix it.

My set has developed a brightness drift - too high when first turned on, drifts darker over a minute or two.
I discovered in my set a number of resistors that drifted badly with heat. I replaced quite a few with NOS carbon composition resistors and and it addressed a number of issues including the brightness drift you described. Perhaps it was just a bad batch of resistors? The replacement carbon resistors do not have the same problem.

As for the selection of the capacitors in the vertical sweep circuit, I was plagued by quite noticeable linearity and height changes in the vertical sweep circuit. I found a number of drifting resistors here and frustrated with it replaced all the resistors in the circuit. It was much better but there was still an minor annoying change in linearity as the set warmed. I recall replacing C512, C513, C508, C507, C511 and C504 a second time to address it. These were all new DigiKey replacements I was obliged to change again with another brand of capacitor and I cannot recall the specific one. But once addressed, the sweep linearity is excellent and there now no noticable change as the set runs.

It just seemed odd to me that despite the capacitors testing good I could not identify the chacteristics of the capacitor change with heat that affected the sweep.
Reply With Quote
  #3  
Old 09-04-2024, 11:13 AM
Alex KL-1 Alex KL-1 is offline
VideoKarma Member
 
Join Date: Jan 2021
Location: Brazil (Paranį)
Posts: 515
Quote:
Originally Posted by Penthode View Post
I discovered in my set a number of resistors that drifted badly with heat. I replaced quite a few with NOS carbon composition resistors and and it addressed a number of issues including the brightness drift you described. Perhaps it was just a bad batch of resistors? The replacement carbon resistors do not have the same problem.

As for the selection of the capacitors in the vertical sweep circuit, I was plagued by quite noticeable linearity and height changes in the vertical sweep circuit. I found a number of drifting resistors here and frustrated with it replaced all the resistors in the circuit. It was much better but there was still an minor annoying change in linearity as the set warmed. I recall replacing C512, C513, C508, C507, C511 and C504 a second time to address it. These were all new DigiKey replacements I was obliged to change again with another brand of capacitor and I cannot recall the specific one. But once addressed, the sweep linearity is excellent and there now no noticable change as the set runs.

It just seemed odd to me that despite the capacitors testing good I could not identify the chacteristics of the capacitor change with heat that affected the sweep.
Capacitors can have surprising temperature coefficients. But, the good ones will be more fair, having near the indicated tempco for it's dieletric.
My guess is caps from not so good maker or bad batch.
Or, it sum and subtract from resistors tempco, then you found ones compensating for that...
__________________
So many projects, so little time...
Reply With Quote
  #4  
Old 09-04-2024, 08:27 PM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
Yes I got a bad batch. Probably my fault as I went for the cheapest.

I recall when I was trying to fix this that magically I must have found the right combination because the drift stopped. But it was only after changing the resistors first and then playing with the capacitors.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:25 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.