Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 08-09-2024, 05:50 PM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
I bought my HP 606B locally thru Facebook Marketplace for $35. It required some repair. But to obtain the accuracy with it or any other marker source, you will require a frequency counter.

Decent sweep generators are easy to find cheaply. Coupling the equipment should be straight forward if you follow the procedure outlined.

You will be able to get the responses depicted only if you have the proper equipment and you can trust your frequency source.

And I only ended up with the HP606B because it was cheap and available. I have have three different HP frequency counters which I obtained over time because they happened to be cheap and were readily available. I believe we live in a fortunate time where so much 1960s and 1970s test equipment which we once could only dream of are now available for next to nothing.

What have you to measure the frequency source accurately?

Last edited by Penthode; 08-09-2024 at 06:06 PM.
Reply With Quote
  #2  
Old 08-09-2024, 06:02 PM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
I want to reluctantly add that I have not be averse to dumpster diving. A local community college was throwing away Wavetek sweep marker generators. The cords were cut off and a few toggle switches were faulty. All easily fixed and it was free. I earlier used an old Precision generator made in Elmhurst NY which I got for free. It needed a few repairs but it worked well. The venerable HP5245L I bought for $25 with a few minor faults. The best addition I made to it was to replace the noisy original fan with a quiet modern computer fan.

I would suggest you first present here your equipment choices and we can provide advice.
Reply With Quote
  #3  
Old 08-09-2024, 06:41 PM
Chris K Chris K is offline
VideoKarma Member
 
Join Date: Jun 2022
Posts: 1,534
Hi all...just a couple of things and questions.

I did the first two steps in the alignment that required the use of the VTVM and I think I was successful.

So yes Penthode, I will detail a list of the equipment I have. Below is what I bought, restored and thought would provide the entire package for doing these alignments.



The way I understood this worked was the RF frequency out is selected using the dial on the right. You select signal strength with the attenuator dials. Sweep width is selected using the sweep dial. Maximum range on this is 10 megacycles. The signal is fed into the desired point(s) on the chassis. If the signal out requires demodulation, it comes back in from the desired point in the circuit using the demodulation cable back into the 369. At that point, a marker is added to the trace selected by the dial on the left and the marker size is adjustable. The processed signal comes out and goes to the scope by the scope out jack which is a funky, special jack that essentially provides a horizontal, vertical and ground signal interpreted on a scope using X-Y mode.

Here are my oscilloscopes...an HP 54600B and a Chinese scope...works well and cost a little over $200 (not that it indicates anything. It was well reviewed)





That's what I got! I don't have a frequency counter or a separate RF generator and sweep generator. I think I have a shelf full of equipment that needs to be scrapped and I'll have to start from scratch!


Some of this has already been done but if my friends can provide some shopping lists and maybe some information on how all of them work together it would be appreciated. I think, at this point, I don't have what I need to dive into the more detailed and intricate steps in this process.
Reply With Quote
  #4  
Old 08-09-2024, 08:03 PM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
I see the Eico sweeper marker generator has a crystal in it. What is it's resonant frequency?

The marker frequencies for the traps were 19.75, 21.25 and 27.25MHz. The bandpass markers that are most important are 22.1, 24.5 and 25.75MHz. The Eico could use the one or perhaps two or three crystals to calibrate it's variable frequency generator.

A cheap shortwave receiver with digital readout could be used to calibrate the marker. The marker accuracy needs to be roughly +/-10kHz particularly with the sound IF and sound traps vs the video carrier 45% position on the slope of the video IF response. The 27.25MHz traps must be fairly accurately set as they will affect the overall IF response. The 19.75MHz traps accuracy is least important.

Historical sidenote affecting the design of the 1948 thru 1952 receivers. This was the time of the TV station construction freeze. 1948 coincided with the sunspot peak and it played havoc with RF reception. Co-channel and adjacent channel interference between stations beyond the RF horizon created headaches for FCC planners. The double upper and lower adjacent channel traps were RCA's answer to alleviate the problem at the time. I recall the summer of 1972 the interference with another sunspot peak. From Toronto Canada reception, KMOX channel 4 in St Louis totally obliterated WBEN channel 4 Buffalo. KDKA channel 2 Pittsburgh would override EGR channel 2 Buffalo. I had an RCA 8T243 (the same chassis as yours which I still have more than 50 years later) and it worked better in these summers than many newer sets. Having more traps was a brilliant idea but it makes alignment more difficult.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:13 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.