Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 07-06-2024, 09:36 PM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
Quote:
Originally Posted by kvflyer View Post
Yes, it is interesting.

I know that it's a PITA but if there are not a lot of connections on the electrolytic capacitor, I disconnect every lead and test the capacitor for value first and leakage at the working voltage next. If it passes, I put everything back and then monitor the temperature. Sometimes you win, sometimes you lose.
When I bought this set about 6 years ago, it had sat in an attic for nearly 60 years unpowered. Apart from a mouse nest, it was a pretty clean and intact set. When I began the restoration, I decided to first evaluate the electrolytics. As it had not been powered on for many years, the filter capacitors were extremely leaky. I believe had it been powered as I found it, the capacitors would have been most likely destroyed and the rectifier destroyed.

I proceeded to reform the electrolytics by simply removing the 5U4 rectifier and with power off, connecting my Sprague TO6 supply across the B+ supply line. I limited the current to a maximum of 10mA and left the TO6 running all night. The voltage across the capacitors began to rise from less than 10 volts @ 10mA. I had taken into account any shunt resistance across the B supply and I recall removing some divider resistances.

The next morning the capacitor voltage had reached nearly 100 volts with minimal leakage. I raised the voltage and keeping maximum leakage less than 10mA. By the end of the day the total paralleled capacitor leakage was well under 1mA. I disconnected a few capacitors I could not readily access to ensure leakage was no more than 100uA at full rated voltage.

The point I am making here is that the capacitors will be destroyed unless a more gentle approach is made waking them up. I never use a variac to power up an old device. I will instead immediately look at the electrolytics and evaluate and see if they will reform. Then if the TV set dates prior to 1960, I will replace almost all the paper capacitors.

I have rebuilt a sizable number of electrolytics which will not reform. But with all 5 of my late 40's RCA Televisions, I have only replaced one chassis mount multiple section electrolytic. My CT100 had two bad chassis mount electrolytics and my CTC5 set has retained all the original electrolytics. Curiously, a 1961 CTC 11 RCA color I restored a decade ago required replacement of every chassis mount electrolytic. All but one the dielectric would not reform and the one that did suddenly failed in service. (The failure was not a short but went totally open.)

So there is no hard and fast rule. It is easy to reform the things and to test leakage and capacitance. And the experience I have had has been very good up to now.

Last edited by Penthode; 07-06-2024 at 09:48 PM.
Reply With Quote
  #2  
Old 07-07-2024, 02:17 PM
kvflyer kvflyer is offline
VideoKarma Member
 
Join Date: Nov 2006
Location: Fernandina Beach, FL
Posts: 1,132
Quote:
Originally Posted by Penthode View Post
When I bought this set about 6 years ago, ...

So there is no hard and fast rule. It is easy to reform the things and to test leakage and capacitance. And the experience I have had has been very good up to now.
And that's the key. No two are alike.
Reply With Quote
  #3  
Old 01-26-2025, 04:08 PM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
Just an update after 4 1/2 years of regular use. Only problem in the last 4 1/2 years was the KRK2 fine tuning shaft. I made a new one out of brass riveted to the original fine tuning disc.

Still using all of the original chassis mount electrolytics. 78 years and still fine. The restoration entailed only replacing the wax caps that needed replacing eg subject to a a large DC across them. A three resistors had drifted affecting operation. Tested transconductance on all tubes and replace a few with original period NOS RCA tubes.

The main point is the originality of the electrolytics. They survived because the set was not plugged in after the set sat unpowered for over 50 years. Slowly reformed the capacitor dielectrics and they are all still fine. One axial lead electrolytic was bad and was replaced.

Here are a couple of snapshots off air made this afternoon. Can you name the film?
Attached Images
File Type: jpg LV1.jpg (86.8 KB, 38 views)
File Type: jpg LV2.jpg (98.4 KB, 30 views)
Reply With Quote
  #4  
Old 11-21-2025, 12:23 AM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
Thought I should resurrect this old thread considering the significance of the originality of my 1947 721TS. I resuscitated this set nearly 5 1/2 years ago and this was to be an experiment to see if a fairly well preserved set could be reliably operated replacing parts only what were absolutely necessary.

In the resuscitation of this set, it retains all but two of it's carbon resistors. About 95% of the paper dielectric capacitors were changed. The ones that were retained were shunted by resistances which swamped the leakage resistance of the capacitors. It retains some of its original tubes. I carefully selected RCA period tube for replacement so it is a fully RCA tubed set. When I received the set 10 years ago, it had sat in a heated attic in a house near Schenectady for just over 50 years. Upon pulling it apart I found a small mouse nest under the chassis and fortunately it caused almost no damage. The set was not powered from the early 1960's until after it's resuscitation in 2020.

However, of major consideration is this set retains all of it's original electrolytic capacitors. This thread describes the extra effort I took to preserve the capacitors. I am not averse to changing the electrolytic ic they test bad. But slowly reforming the dielectric on each electrolytic in this set brought them all back with very low leakage.

So the bet was on as to how long they would last? I power the set on average once a week and let it run for a couple of hours. I decided to check the capacitors this evening and can report that they all appear fine.

Here after 5 1/2 years, after the careful reforming of all the original electrolytic cans, are some off air shots. (I did replace the original 40uF axial lead electrolytic but all the chassis mounted cans are now 78 years old.
Attached Images
File Type: jpg 721TS_2_251120-min.jpg (36.2 KB, 31 views)
File Type: jpg 721TS_1_251120-min.jpg (36.9 KB, 29 views)

Last edited by Penthode; 11-21-2025 at 10:40 AM.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:59 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.