Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 06-21-2024, 12:51 PM
Yamamaya42's Avatar
Yamamaya42 Yamamaya42 is offline
VideoKarma Member
 
Join Date: Nov 2018
Location: Round Rock TX
Posts: 3,253
The exact value is not super critical, since there is so little voltage to start with, people have used a .1 or .01 film type with out problems.
__________________
=^-^=
Yasashii yoru ni hitori utau uta. Asu wa kimi to utaou. Yume no tsubasa ni notte.
いとおしい人のために
Reply With Quote
  #2  
Old 06-21-2024, 06:57 PM
Chris K Chris K is offline
VideoKarma Member
 
Join Date: Jun 2022
Posts: 1,534
Quote:
Originally Posted by Yamamaya42 View Post
The exact value is not super critical, since there is so little voltage to start with, people have used a .1 or .01 film type with out problems.
No change in symptoms with a composite signal into the 1st video grid. R130 is reading 180 ohms and not 150 ohm. I got the freeze spray today.
Reply With Quote
  #3  
Old 06-21-2024, 07:33 PM
Yamamaya42's Avatar
Yamamaya42 Yamamaya42 is offline
VideoKarma Member
 
Join Date: Nov 2018
Location: Round Rock TX
Posts: 3,253
Quote:
Originally Posted by Chris K View Post
No change in symptoms with a composite signal into the 1st video grid. R130 is reading 180 ohms and not 150 ohm. I got the freeze spray today.
BINGO!

That is out of tolerance for 10%
and you may have others, some say that having it go higher than 20% is OK, but in my case, I checked each and EVERY resistor, using this site, https://www.allaboutcircuits.com/too...de-calculator/
If it tested within 10% or better, I marked it with green paint, if it checked below, I replaced with a new 1% resistor, This could be your problem, not sure, but It is what I had to go through
__________________
=^-^=
Yasashii yoru ni hitori utau uta. Asu wa kimi to utaou. Yume no tsubasa ni notte.
いとおしい人のために
Reply With Quote
  #4  
Old 06-21-2024, 08:05 PM
Chris K Chris K is offline
VideoKarma Member
 
Join Date: Jun 2022
Posts: 1,534
Replaced the R130 resistor with a 1% 150 ohm and it is better. It's not stable, it still twitches but it hasn't gone completely out of sync like it was before. Voltage hasn't changed much but I think going through this and replacing resistors across the board in the IF circuits is something I should do. The 1500pf caps as well.
Reply With Quote
  #5  
Old 06-21-2024, 09:06 PM
Yamamaya42's Avatar
Yamamaya42 Yamamaya42 is offline
VideoKarma Member
 
Join Date: Nov 2018
Location: Round Rock TX
Posts: 3,253
Quote:
Originally Posted by Chris K View Post
Replaced the R130 resistor with a 1% 150 ohm and it is better. It's not stable, it still twitches but it hasn't gone completely out of sync like it was before. Voltage hasn't changed much but I think going through this and replacing resistors across the board in the IF circuits is something I should do. The 1500pf caps as well.
Not sure why you chose 150s to replace the 130s, as the IF is always picky, but most likely, as you go through the whole set and replace all out of tol resistors no matter what section, things will get more stable, this of course will take a lot of time, it took me 2-3 months to do mine staring with a very unstable pic, to what I have now.
__________________
=^-^=
Yasashii yoru ni hitori utau uta. Asu wa kimi to utaou. Yume no tsubasa ni notte.
いとおしい人のために
Reply With Quote
Audiokarma
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:06 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.