Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Rectangular Screen Tube Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 07-21-2023, 09:35 AM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
If those resistors are truly as low as you are measuring then they are badly out of tolerance and need to go ASAP....That said it's been a while since I've looked at the schematic and there could be a parallel path creating a false reading. In any event if you don't want to be doing tons of cross referencing for replacement transistors that might get damaged, then your next move should be to unsolder a leg of each of those resistors and double check how they measure and IMMEDIATELY change them if they have drifted low and are out of tolerance.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
  #2  
Old 07-21-2023, 05:18 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
Quote:
Originally Posted by Electronic M View Post
If those resistors are truly as low as you are measuring then they are badly out of tolerance and need to go ASAP....That said it's been a while since I've looked at the schematic and there could be a parallel path creating a false reading.
Do you happen to remember the + source those two resistors are fed from? Seems like it as a lot higher than 24V, but I could be wrong. Also I could be wrong on the 27K value, but that's the figure that sticks in mind. A schematic would sure be handy.
Reply With Quote
  #3  
Old 07-21-2023, 06:33 PM
zeno's Avatar
zeno zeno is offline
VideoKarma Member
 
Join Date: Mar 2013
Location: New Hampshire
Posts: 4,918
The resistors looked "different". IIRC they turned color & got a bubbly
coating on them. Lift one end & retest them.
Same with transistors not in sockets. Lift 2 out of 3 leads & test with
DVM on diode test. We had a few transistor checkers & they collected dust.
Only one tech used them & he was playing engineer & wasting time.
Bottom line is parts IN circuit very often read bad.

73 Zeno
LFOD !
Reply With Quote
  #4  
Old 07-21-2023, 07:39 PM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
Quote:
Originally Posted by old_coot88 View Post
Do you happen to remember the + source those two resistors are fed from? Seems like it as a lot higher than 24V, but I could be wrong. Also I could be wrong on the 27K value, but that's the figure that sticks in mind. A schematic would sure be handy.
Unfortunately no, but 98% chance I have the schematic. I'm hoping to have bench time this weekend, maybe I can dig it up while I'm down there.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
  #5  
Old 07-22-2023, 12:31 AM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
I saw that my Sylvania TV is in Sam's 1045-2 which I don't have a physical copy of and I try to avoid buying the PDF copies from them unless I have no choice in the matter because I think its ridiculous to charge $22 for a PDF reproduction of an original service manual that may or may not be of that great of quality compared to the original paper document, and feebay is hit or miss on having original Sam's Photofacts for sale, and some times they want just as much on feebay for an original Paper copy as Sam's does for a PDF reproduction. Which is why if someone on here has an original paper copy that they can scan and upload I prefer to go that route rather than having to pay $22 for a photocopy of an original Sam's, or if I can hold out for someone locally that might have a bunch of old sam's folders that they are liquidating from their collection for a decent price, like what Shango did.
Reply With Quote
Audiokarma
  #6  
Old 07-22-2023, 01:00 AM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Well, I did suprisingly enough manage to find an original hard copy of Sam's folder #1045 (the whole folder, not just one of the sections out of the folder) for $9 plus shipping.

But I had to search a little bit because there weren't many listings for individual Sam's folders, they were mostly just listing the compilation books or selling a set of Photofact Folders as a lot (with one such listing being listed for $800 for a set of 50 complete Photofact folders that were in no particular order) with only 2 listings that were selling individual folders out of a lot of 50 or 100 Sam's Folders, that I'm assuming came from an old repair shop or an old Library collection.
The one listing that was selling individual folders out of a full lot of Sam's folders had Folder 1045 but it was already sold, and the second listing had 2 Sam's 1045 folders and one had already sold and I had just bought the last one out of that lot.

So it seems that these Sam's folders are getting harder to come by unfortunately.
Reply With Quote
  #7  
Old 07-23-2023, 08:20 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by old_coot88 View Post
Do you happen to remember the + source those two resistors are fed from? Seems like it as a lot higher than 24V, but I could be wrong. Also I could be wrong on the 27K value, but that's the figure that sticks in mind. A schematic would sure be handy.
According to the circuit Board the + Voltage feeding those resistors is +340 volts.

According to the resistor color coding on the 2 2W carbon comp resistors you're referring to are supposed to be 68k Ohm resistors and then there are 3 green wirewound resistors on the same board that are 27k Ohm 3W power resistors which all measure within spec yet, but the 2 2W Carbon Comp Resistors which are supposed to be 68k Ohms are measuring only 16k Ohms or so, so it sounds like those carbon comp resistors need to go bye-bye, because they are WAAAAAYYYY out of tolerance.

Probably what I'll do to replace those 2W 68k Ohm resistors is cut them off on either side of the resistor element casing and then solder a new one onto what's left of the wire connectors above the board so that way I don't have to worry about risking damaging the circuit traces underneath the board, since they left about a 1/4" of wire lead above the board surface.
Reply With Quote
  #8  
Old 07-23-2023, 10:03 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
IMHO you'd be better off waitin for a Sams to double-verify those resistors' value. Code stripes can change color from excessive heat over long duration. Gotta wonder if the two transistors might still be good though.
Reply With Quote
  #9  
Old 07-24-2023, 12:02 AM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by old_coot88 View Post
IMHO you'd be better off waitin for a Sams to double-verify those resistors' value. Code stripes can change color from excessive heat over long duration. Gotta wonder if the two transistors might still be good though.
I have a Sam's on order from feebay, that is an original full 1045 Folder that I got for $13, it supposed to be here sometime this week.

When I get that folder I'll take a look at the manual for the TV and double check the resistor values.
Reply With Quote
  #10  
Old 07-26-2023, 07:08 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
I got the manual for my TV in the mail today and I just confirmed that the 2 2W Carbon Comp resistors in the TV were indeed 68k Ohm 2 watt resistors and what I was measuring on them using my VTVM was about 16k Ohms which is indeed way low.

And I believe that VTVMs can be used to measure resistors in circuit regardless of there being a parallel load on them or not because the VTVM applies a voltage to the resistor when measuring it that makes it read like the resistor is out of circuit, at least that's my understanding of how VTVMs work, compared to DMMs.
Reply With Quote
Audiokarma
  #11  
Old 07-27-2023, 12:19 AM
old_tv_nut's Avatar
old_tv_nut old_tv_nut is offline
See yourself on Color TV!
 
Join Date: Jul 2004
Location: Rancho Sahuarita
Posts: 7,815
Quote:
Originally Posted by vortalexfan View Post
....And I believe that VTVMs can be used to measure resistors in circuit regardless of there being a parallel load on them or not because the VTVM applies a voltage to the resistor when measuring it that makes it read like the resistor is out of circuit, at least that's my understanding of how VTVMs work, compared to DMMs.
That is not correct for an type of resistance meter. When a resistor is still in the circuit, other conducting paths will be measured in parallel with the resistor, which will make it read low. How much lower depends on what is in parallel in the circuit. This is a property of the circuit, not the meter.
__________________
www.bretl.com
Old TV literature, New York World's Fair, and other miscellany
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:52 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.