Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Rectangular Screen Tube Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 07-20-2023, 08:35 AM
JohnCT's Avatar
JohnCT JohnCT is offline
VideoKarma Member
 
Join Date: Jan 2020
Posts: 749
I wouldn't run it any further until I verified the carbon resistors that feed the transistor section have not dropped in value. I remember having one about 50 years ago that trashed every transistor and choke coil in the chroma/video section by dumping 2X the voltage into the signal circuits.

John
Reply With Quote
  #2  
Old 07-20-2023, 10:17 AM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by JohnCT View Post
I wouldn't run it any further until I verified the carbon resistors that feed the transistor section have not dropped in value. I remember having one about 50 years ago that trashed every transistor and choke coil in the chroma/video section by dumping 2X the voltage into the signal circuits.

John
OK, will do, I'll check every resistor in that section of the TV and make sure they haven't drifted up in value.
Reply With Quote
  #3  
Old 07-20-2023, 12:48 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
FWIW (it may not apply in this case), we ran into some Sylvania hybrids that had two 2 watt carbon comp resistors that chronically cook and go 'waay low in value. IIRC they were something like 27K and dropped to a few hunderd ohms. They were the collector load resistors for the two demod transistors, which shorted from overcurrent. Apparently the resistors' phenolic casing charred to carbon over time, shunting the resistive elements.

Edit... those two resistors may have been more like 2.7K, not 27K. Been a lotta years.

Last edited by old_coot88; 07-20-2023 at 10:34 PM.
Reply With Quote
  #4  
Old 07-20-2023, 01:02 PM
zeno's Avatar
zeno zeno is offline
VideoKarma Member
 
Join Date: Mar 2013
Location: New Hampshire
Posts: 4,918
Quote:
Originally Posted by old_coot88 View Post
FWIW (it may not apply in this case), we ran into some Sylvania hybrids that had two 2 watt carbon comp resistors that chronically cook and go 'waay low in value. IIRC they were something like 27K and dropped to a few hunderd ohms. They were the collector load resistors for the two demod transistors, which shorted from overcurrent. Apparently the resistors' phenolic casing charred to carbon over time, shunting the resistive elements.
Ditto
I only saw it on the portables but first thing to check. Basically it
put 200+ volts on the 24 V line. Things explode !

Rolling may be from the AGC oops. If the tuner is SS there may be 2
controls. IF AGC & RF AGC.

Zeno
Reply With Quote
  #5  
Old 07-21-2023, 12:56 AM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by zeno View Post
Ditto
I only saw it on the portables but first thing to check. Basically it
put 200+ volts on the 24 V line. Things explode !

Rolling may be from the AGC oops. If the tuner is SS there may be 2
controls. IF AGC & RF AGC.

Zeno
The tuner on this TV is Solid state according to the tube & transistor placement chart on the back of the TV.

The AGC adjustment that I accidentally diddled was the one that was next to the Vertical Linearity and Height Adjustments, which I was trying to adjust those because of the vertical roll that I couldn't lock in, and the AGC flub caused the picture to do some sort of weird thing where the picture looked like a red and blue candycane stripe going down the screen with some other strange screen distortions mixed in.

The 2 watt resistors you were talking about aren't burnt to a crisp or anything in my TV (they actually look like brand new yet) but they do measure a little low (around 10k-15k ohms rather than the 27k ohms that they should measure, but they don't measure in the hundreds of ohms range that you said they would measure if they were truly bad.)

As for trying to measure whether or not the transistors were bad or shorted, I don't have a transistor checker but I do have a DMM with a diode check mode but the transistors are so small and have such small leads that none of my test probes or aligator clip adaptors for my DMM test probes will fit onto the transistor leads without touching each other.

Do you have any suggestions as to a way to test these transistors without either damaging them or having to spend a whole lot of money on an expensive transistor tester?
I know the $5 Harbor Freight Special DMM had a dedicated transistor tester section but I'm not sure how accurate it is as I've never had a chance to use that function on one of those before (I did have one of those $5 Harbor Freight Special DMMs that I picked up NOS at Goodwill once but it broke on me before I had a chance to extensively try out all of the features on it.)
Reply With Quote
Audiokarma
  #6  
Old 07-21-2023, 09:37 AM
zeno's Avatar
zeno zeno is offline
VideoKarma Member
 
Join Date: Mar 2013
Location: New Hampshire
Posts: 4,918
Transistors on old Sylvanias usually plug in to little white
sockets. Just be careful they go back in rite !

Zeno
Reply With Quote
  #7  
Old 07-21-2023, 04:57 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
Quote:
Originally Posted by vortalexfan View Post

Do you have any suggestions as to a way to test these transistors without either damaging them or having to spend a whole lot of money on an expensive transistor tester?
Dunno how well this test would work with a digital ohm meter, but seems like it should provided the test voltage on the leads is proper polarity. I use a Simpson 260 analog meter set on highest R scale. The transistor needs to be NPN type (which your are) and out of circuit. You must identify which pins are emitter, base and collector, and bend at least two pins just enuff to attach clip leads.
Clip negative lead to emitter, positive to collector. Meter should read open circuit. Now moisten a fingertip and touch between base and collector. Resistance should drop as transistor turns on, indicating gain. (In the rare instance of testing a PNP transistor, just reverse the meter leads.)
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:16 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.