Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early Color Television

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 12-11-2022, 12:55 PM
Yamamaya42's Avatar
Yamamaya42 Yamamaya42 is offline
VideoKarma Member
 
Join Date: Nov 2018
Location: Round Rock TX
Posts: 3,254
Live video is very different from a still static non moving image.
As others have mentioned, when you fine tune the set, if you get color shifting especially in the reds, it's a sign that the IF is out of alignment, and it is not unusual for it to be able to lock with a test pattern and not a live video.
__________________
=^-^=
Yasashii yoru ni hitori utau uta. Asu wa kimi to utaou. Yume no tsubasa ni notte.
いとおしい人のために
Reply With Quote
  #2  
Old 12-11-2022, 03:49 PM
zeno's Avatar
zeno zeno is offline
VideoKarma Member
 
Join Date: Mar 2013
Location: New Hampshire
Posts: 4,918
UNLESS its the camera the live pix is TOO DAMN BRITE !!!
The set is still on its side also. If it is in reality when you get it
back on its feet you will need to re do the set up.
You should be able to turn the color, brite & contrast down & extinguish
the raster or nearly so. These sets were NOT brite ! In the day most
watched them in a darkend room with curtains drawn.
This is NOT a Chromacolor, Trinitron, EFL or FTM CRT that you could light
a room with. If you overdue the brite everything starts to fall apart pix wise

As for generators we did 90% of our set ups were by eye. Live shows worked
better for us & give a real world look at the pix. Try it. No confusing mirror,
just lay across the set, look at pix & reach back to adj. SO much easier.
Also generators can add problems if the TV's controls are not set right.

One last thing. Put up a pix of the set with NO signal, just snow. Snow
can tell you a lot believe it or not.

73 Zeno
Reply With Quote
  #3  
Old 12-11-2022, 04:15 PM
Yamamaya42's Avatar
Yamamaya42 Yamamaya42 is offline
VideoKarma Member
 
Join Date: Nov 2018
Location: Round Rock TX
Posts: 3,254
Quote:
Originally Posted by zeno View Post
UNLESS its the camera the live pix is TOO DAMN BRITE !!!
The set is still on its side also. If it is in reality when you get it
back on its feet you will need to re do the set up.
You should be able to turn the color, brite & contrast down & extinguish
the raster or nearly so. These sets were NOT brite ! In the day most
watched them in a darkend room with curtains drawn.
This is NOT a Chromacolor, Trinitron, EFL or FTM CRT that you could light
a room with. If you overdue the brite everything starts to fall apart pix wise

As for generators we did 90% of our set ups were by eye. Live shows worked
better for us & give a real world look at the pix. Try it. No confusing mirror,
just lay across the set, look at pix & reach back to adj. SO much easier.
Also generators can add problems if the TV's controls are not set right.

One last thing. Put up a pix of the set with NO signal, just snow. Snow
can tell you a lot believe it or not.

73 Zeno
the live pic looks crappy because the input video being fed to test point B is 4-5 times too low, the TV expects 5v PtP going into the 1st video amp, but w/o an amp to boost it, it is only getting 1v, and will have a washed out picture when fed direct video to that point no matter the brightness level setting.

And the reason the set is on it's side is that it has the access panel removed on the bottom to reach the underside easily for service with the chassis still installed.
It's prob petty much understood that once the set is upright and in it's final location, a final purity and convergence will need to be done again, as is always with these sets.
__________________
=^-^=
Yasashii yoru ni hitori utau uta. Asu wa kimi to utaou. Yume no tsubasa ni notte.
いとおしい人のために
Reply With Quote
  #4  
Old 12-11-2022, 04:30 PM
timmy's Avatar
timmy timmy is offline
VideoKarma Member
 
Join Date: Jan 2011
Location: Delaware ny
Posts: 3,719
Quote:
Originally Posted by Yamamaya42 View Post
the live pic looks crappy because the input video being fed to test point B is 4-5 times too low, the TV expects 5v PtP going into the 1st video amp, but w/o an amp to boost it, it is only getting 1v, and will have a washed out picture when fed direct video to that point no matter the brightness level setting.

And the reason the set is on it's side is that it has the access panel removed on the bottom to reach the underside easily for service with the chassis still installed.
It's prob petty much understood that once the set is upright and in it's final location, a final purity and convergence will need to be done again, as is always with these sets.
Yes that’s right about how the pic looks and the set is on all 4 legs. Overall the pic looks good considering all these problems with this set colors look better then previous pics.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:39 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.