Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 09-21-2022, 08:51 PM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
Quote:
Originally Posted by kvflyer View Post
That's encouraging since I have an RCA 630TS that I purchased a few years ago. It is in great condition; the GE replacement CRT measures NOS. I guess I should bring it up slowly on my Sencore PR-57, monitoring the current and see what happens. I don't mind rebuilding the capacitors but if they hold good, why not???

Thanks for the encouraging update.
You could do it slowly that way. What I prefer is to put a current limited DC power supply across the electrolytics with power off. With the tubes not conducting and with a study of the schematic to see what bleeders are across the B plus, you can better gauge the condition of the electrolytics. In some cases I simply disconnect the electrolytics to better isolate to confirm the condition of the electrolytic.

I have restored set that must have been dormant for 50 years of more. My RCA 721TS the seller near Schenectady NY told me my 721TS was stuch in the attic in the early 60's and was not touched until they sold it to me in 2016. I cleaned out a mouse nest but didn't start to restore it until 2020. It absolutely had not been powered in the meantime so it likely sat unpowered for 60 years. Incredible when you think about it.

And that is what I think saved the electrolytics. I gently brought up the capacitors by limiting the current to no more that about 10mA per capacitor. If the set has sat for decades, the capacitors will be almost a dead short and it is almost certain the capacitors will be destroyed. Yhe key is to carefully monitor and ensure the current is strictly limited until the dielectric has properly reformed.

I would leave the DC supply on for the night and inch the voltage upwards while monitoring the current. When it reached close to the rated maximum voltage, the electrolytic, if healthy, it will draw only about 100uA. If the capacitors draw more than 1mA after reforming, then it must be restuffed.

To summarize, I do not like using a Variac to first power up. To me it is the lazy man approach to the problem and because you are more adequately monitoring the current, it is hit and miss. By using a high voltage DC supply with current and voltage monitoring, you can better decide whether the capacitor is a survivor or not.

Proof should be the 721TS which has lasted over two years on ALL the aluminum can capacitors. I am in the midst of restoring a CT100 color set (which when I have time again in a few weeks will get down to the final alignment) which I slowly reformed the capacitors with the DC supply. All have survived and work fine.
Reply With Quote
  #2  
Old 09-22-2022, 10:23 AM
kvflyer kvflyer is offline
VideoKarma Member
 
Join Date: Nov 2006
Location: Fernandina Beach, FL
Posts: 1,132
Quote:
Originally Posted by Penthode View Post
You could do it slowly that way. What I prefer is to put a current limited DC power supply across the electrolytics with power off. With the tubes not conducting and with a study of the schematic to see what bleeders are across the B plus, you can better gauge the condition of the electrolytics. In some cases I simply disconnect the electrolytics to better isolate to confirm the condition of the electrolytic....
I have a Heathkit High Voltage Power Supply, IP-17 which I have totally restored. It has voltage and current meters so it would be easy to do.

I have a working T100 that came up on all original electrolytic capacitors. But I have not turned it on for about 8-10 years though. It was rather easy to get going.
Reply With Quote
  #3  
Old 09-23-2022, 09:04 AM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
Quote:
Originally Posted by kvflyer View Post
I have a Heathkit High Voltage Power Supply, IP-17 which I have totally restored. It has voltage and current meters so it would be easy to do.

I have a working T100 that came up on all original electrolytic capacitors. But I have not turned it on for about 8-10 years though. It was rather easy to get going.
8 to 10 years off, if the capacitors were previously good, I dont think will be a problem. I think it is a problem when it has been off for 40 or more years with a sudden power up..

If you use the DC HV power supply across the B plus line to reform the capacitors, I will be interested in your results.
Reply With Quote
  #4  
Old 12-08-2022, 05:19 PM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
The set has now been running faultlessly since July 2020. That is two and a half years still running on the original electrolytics. Still no sign of failure.
Attached Images
File Type: jpg 20221208_171315.jpg (52.2 KB, 47 views)
File Type: jpg 20221208_171319.jpg (40.8 KB, 45 views)
Reply With Quote
  #5  
Old 12-09-2022, 11:02 AM
kvflyer kvflyer is offline
VideoKarma Member
 
Join Date: Nov 2006
Location: Fernandina Beach, FL
Posts: 1,132
Great to see this update and you have given me an incentive. I have an RCA 630TS that is in excellent physical condition and has all of the parts. The GE CRT, no doubt a replacement, tests NOS. I will start with replacing the paper capacitors in the sweep sections and audio and see how the electrolytic capacitors reform. Carefully, slowly! Thanks.
Reply With Quote
Audiokarma
  #6  
Old 08-23-2023, 10:21 AM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
It has now been three years since I resuscitated this set. Recall all of the original electrolytics except for a replaced 40uFd axial lead unit are original. Most of the paper dielcetric capacitors were changed. I left a few units which were bypassed by resistors less than 100Kohm. And a few resistors which I found drifted when it affected performance. I then decided to run the set regularly and report from time to time on it's performance over the years. It is well past 1500 hours.

The set has developed two problems:
1. The original KRK2 tuner fine tuning has a bad back lash which make it difficult to fine tune. I believe it has to do with the slop in the shafte which I have to address. The second is a horizontal sync issue which causes the horiztal oscilaator phase to shift briefly and jump back. It is very momemtary and occurs rarely. Have no idea what it may be and keeping an eye on it.

But this set has been incredibly reliable and delivers a very good picture for a set which is 76 years old. Here are a few snapshots from over the air CHCH TV channel 11 this morning.
Attached Images
File Type: jpg I Love Lucy 1.jpg (121.0 KB, 31 views)
File Type: jpg I Love Lucy 2.jpg (129.4 KB, 22 views)
File Type: jpg I Love Lucy 3.jpg (141.9 KB, 19 views)
Reply With Quote
  #7  
Old 11-20-2023, 10:58 AM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
Latest update on the 721TCS.

From the original 2020 restoration:

All the original can electrolytics are still fine with no problem That makes them 76 years old!

I left many of the original wax capacitors which pose no threat due to leakage. The ones I left are shunted by resistances 1M ohm or less and pose no DC threat.

Only two resistors changed asthey affected performance (horizonal plate resistor and video amp plate resistor.

An axial lead 40uF capacitor changed due to leakage.

Recent service:

KRK2 tuner fine tuning problem - slop due to wear in the brass tuning wand worn making it hard to tune for best sound (recall this is a split sound set). I made a new brass wand and attached it to the original tuning shaft disc. The repair fixed perfectly the fine tuning issue.

Horizontal jumping. the picture would jitter horizontally due to what appearred to be a time constant change in the circuit. Changed 6SN7 oscillator tube which fixed the problem.

Set remains working fine after regular 3 1/2 years use on all original electrolytic capacitors.

Here is a screen shot from this morning with the signal from an over the air signal via an ATSC set top box.
Attached Images
File Type: jpg 721TS_231120a.jpg (143.0 KB, 33 views)

Last edited by Penthode; 11-20-2023 at 07:43 PM.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:13 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.