Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early Color Television

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 09-08-2022, 10:51 PM
etype2's Avatar
etype2 etype2 is offline
VideoKarma Member
 
Join Date: Mar 2010
Location: Valley of the Sun, formerly Silicon Valley, formerly Packer Land.
Posts: 1,643
From my experience, I would agree resolution is reduced on this site. Your chassis photos look good. I upload photos from another server and post a link.
__________________
Reply With Quote
  #2  
Old 11-29-2022, 11:35 PM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
It has been a couple of months since I worked on the CT100. Too many diversions made me put this aside for a couple of months. With the onset of winter, I have the chassis back on the bench and have begun the full IF alignment.

The sound IF discriminator alignment was very straightforward. I have just completed the final IF stage sweep alignment and the traps required a minor tweak. The response matches the service data exactly. I am documenting the entire process so there will be more to come on this.

I was proceeding to do the full IF sweep alignment when I made an interesting discovery. The procedure requires applying a -6.0 volts to the IF line and to connect to chassis ground the junction of 2R133 and 2R134. First I see no 2R133 in the v117 (6AN8) plate circuit so assume it was a typo: I see only a 2C133 connected to 2R134.

I am looking forward to examining the chroma and luma channel responses and posting what I see here.

Last edited by Penthode; 11-29-2022 at 11:57 PM.
Reply With Quote
  #3  
Old 12-02-2022, 12:56 AM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
Run into a bit of a snag with the IF alignment.

Lined up the Audio IF and the last (6th) IF stage with no problem. The first IF stage (6U8) located on the tuner I cannot achieve the RCA published response curve. The coupling transformer between the 1st and 2nd IF stage must provide a wide bandpass. I have stagger tuned the primary and secondary in an attempt to secure the best response. the sweep alignment is supposed to include a 6MHz bandpass with a litle dip in the middle. the best I can provide is a hump in the middle with the low frequency end at 41.25MHz elevated above 45.75MHz.

Using the prescribed input head to couple to the mixer diode and from the testpoint through the detector block through T1, the signal is fed to the 6U8 in a common grid amplifier configuration which then is coupled to the grid of the 6U8 pentode section. The output is coupled to the tuner IF output via transformer T2. The detector block is connected to point T2 at the plate of the penthode section of the 6U8 on the diagram. The response curve is not affected by stray capacitance or moving the cables. It is a good consistent trace. I swapped the 6U8 (with NOS 6U8A's) and there is no change.

I am using for the sweep generator an HP8601a and the marker is it's companion HP8600a. The HP equipment is very precise and perfect for television sweep alignment. The swwep alignment of the detector stage matches exactly the picture in the notes.

With the response I achived so far with this coupling, the poor response adversely affects the subsequent sweep alignment from the mixer to the second IF stage as prescribed. Hence I have gone back to investigate further.

My plan next is to pull the tuner top and have a look at the transformer and components around it. The great thing is I may not even have to disconnect any connections as the complete tuner chassis holding the RF amplifier, mixer, oscillator and 1st IF stage is easily removed from the tuner box by removing a few screws.

Curious note: the rest of the curves depict low frequency to the left and high frequency to the right. You would normally get a reversal when the signal is hetrodyned or mixed with a local oscillator with frequency about the desired incoming. In this case no hetrodyning is done so why do the notes show a reversal? I checked Sams notes and they copied the RCA diagram exactly.

Whether you are familiar or not with this tuner, I would appreciate your comments.
Attached Images
File Type: jpg 1st IF coupling.jpg (51.5 KB, 25 views)
File Type: jpg 1st IF Coupling 2.jpg (67.0 KB, 24 views)
File Type: jpg 1st IF Coupling 3.jpg (70.6 KB, 19 views)
File Type: jpg tuner1.jpg (81.1 KB, 26 views)

Last edited by Penthode; 12-02-2022 at 11:01 AM.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:13 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.