Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 08-23-2022, 10:10 PM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
Oh you shouldn't have touched the discriminator or if transformers!! To align it requires proper equipment!!

Never mind for now. There was nothing wrong with the IF adjustments. The problem is most likely the local oscillator in the tuner is off frequency.

Because you have messed with the adjustments, you may now have lost the reference between sound and video. The best thing is to not touch any of the IF adjustments and try and get sound by slowly adjusting the tuner oscillator frequency adjustment.

So long as the discriminator and IF adjustments are back to where they were, you should be okay.

I looked at the 721TS notes and I do not see a master oscillator adjustment. I suggest you first try exchanging the oscillator with the other 6J6 tubes in the tuner to see if that brings back the audio.

Last edited by Penthode; 08-24-2022 at 01:04 AM.
Reply With Quote
  #2  
Old 08-24-2022, 06:59 AM
Chris K Chris K is offline
VideoKarma Member
 
Join Date: Jun 2022
Posts: 1,534
Quote:
Originally Posted by Penthode View Post
Oh you shouldn't have touched the discriminator or if transformers!! To align it requires proper equipment!!

Never mind for now. There was nothing wrong with the IF adjustments. The problem is most likely the local oscillator in the tuner is off frequency.

Because you have messed with the adjustments, you may now have lost the reference between sound and video. The best thing is to not touch any of the IF adjustments and try and get sound by slowly adjusting the tuner oscillator frequency adjustment.

So long as the discriminator and IF adjustments are back to where they were, you should be okay.

I looked at the 721TS notes and I do not see a master oscillator adjustment. I suggest you first try exchanging the oscillator with the other 6J6 tubes in the tuner to see if that brings back the audio.
Where is the tuner oscillator adjustment located? Is this the T3 transformer I mentioned or is it somewhere in the tuner shielded box?
Reply With Quote
  #3  
Old 08-24-2022, 10:01 AM
Chris K Chris K is offline
VideoKarma Member
 
Join Date: Jun 2022
Posts: 1,534
Quote:
Originally Posted by Penthode View Post
Oh you shouldn't have touched the discriminator or if transformers!! To align it requires proper equipment!!

Never mind for now. There was nothing wrong with the IF adjustments. The problem is most likely the local oscillator in the tuner is off frequency.

Because you have messed with the adjustments, you may now have lost the reference between sound and video. The best thing is to not touch any of the IF adjustments and try and get sound by slowly adjusting the tuner oscillator frequency adjustment.

So long as the discriminator and IF adjustments are back to where they were, you should be okay.

I looked at the 721TS notes and I do not see a master oscillator adjustment. I suggest you first try exchanging the oscillator with the other 6J6 tubes in the tuner to see if that brings back the audio.
I pulled up the schematic (I'm at work ) and there are oscillator coil adjustments for each channel. Are you saying adjust for each channel or is there a general tuner oscillator adjustment available?? I don't see one.
Reply With Quote
  #4  
Old 08-24-2022, 06:52 PM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
On the older KRK2 tuner used in this set, there is a screw for each channel. But before you touch those, it is worthwhile to swap 6J6 tubes around. The inter-electrode capacitance difference between tubes may be sufficient to bring the tuning within range of the audio. Try exchanging the oscillator with the two othe 6J6s to check that out.

You do not have to worry about the front end RF tuning because the tuning is very broad. The oscillator is the critical one and you have to be within a few hundred kHz to hear anything.
Reply With Quote
  #5  
Old 08-25-2022, 01:58 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by Penthode View Post
On the older KRK2 tuner used in this set, there is a screw for each channel. But before you touch those, it is worthwhile to swap 6J6 tubes around. The inter-electrode capacitance difference between tubes may be sufficient to bring the tuning within range of the audio. Try exchanging the oscillator with the two othe 6J6s to check that out.

You do not have to worry about the front end RF tuning because the tuning is very broad. The oscillator is the critical one and you have to be within a few hundred kHz to hear anything.
Couldn't one hook his digital to analog converter box set to Ch 3 or 4 rf carrier(no antenna) to the set's ant input and monitor the DC voltage at the output(pin 1) of 6AL5(V116) sound discriminator? With the TV's ch selector set to the corresponding carrier frequency it seems pin 1 should be at or very near 0v DC when everything is aligned correctly. If this works I'd set the fine tuning to center and adjust the Ch 3 or 4 oscillator slug in attempt to read 0 DC volts at pin 1. This assuming the sound IF and discriminator adjustments are very near their previous tampered with settings.
Reply With Quote
Audiokarma
  #6  
Old 08-25-2022, 05:08 PM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
Quote:
Originally Posted by Kevin Kuehn View Post
Couldn't one hook his digital to analog converter box set to Ch 3 or 4 rf carrier(no antenna) to the set's ant input and monitor the DC voltage at the output(pin 1) of 6AL5(V116) sound discriminator? With the TV's ch selector set to the corresponding carrier frequency it seems pin 1 should be at or very near 0v DC when everything is aligned correctly. If this works I'd set the fine tuning to center and adjust the Ch 3 or 4 oscillator slug in attempt to read 0 DC volts at pin 1. This assuming the sound IF and discriminator adjustments are very near their previous tampered with settings.
Yes you could. However you will hear the audio as you are tuning the slug long before you will have anything intelligible on the meter. Further you can hear when it is tuned as you will be tuning between the two distortion peaks if the discriminator is properly aligned for a perfect s response. The alignment remains suspect now because the settings have been changed. But even if the alignment is bad, you should hear something.

So the first rudimentary step is to try and bring the local oscillator back in line. I suspect a simple swap around of the tubes will yield some audio. Then we can focus on its precise final adjustment.

Which reminds me that split sound TV tuning is no different from an FM radio tuning which uses the discriminatory circuit. That is as you approach the correct tuning, the audio builds in level, becomes distorted then the loudest and clearest audio is received. Tuning further you reach a second distortion peak and the audio clears and is weaker. Many forget that either side of the best audio point is slope detection which is weaker and slightly distorted.

But here, we first need to hear any audio and the home in on it.
Reply With Quote
  #7  
Old 08-25-2022, 05:22 PM
Chris K Chris K is offline
VideoKarma Member
 
Join Date: Jun 2022
Posts: 1,534
Quote:
Originally Posted by Penthode View Post
Yes you could. However you will hear the audio as you are tuning the slug long before you will have anything intelligible on the meter. Further you can hear when it is tuned as you will be tuning between the two distortion peaks if the discriminator is properly aligned for a perfect s response. The alignment remains suspect now because the settings have been changed. But even if the alignment is bad, you should hear something.

So the first rudimentary step is to try and bring the local oscillator back in line. I suspect a simple swap around of the tubes will yield some audio. Then we can focus on its precise final adjustment.

Which reminds me that split sound TV tuning is no different from an FM radio tuning which uses the discriminatory circuit. That is as you approach the correct tuning, the audio builds in level, becomes distorted then the loudest and clearest audio is received. Tuning further you reach a second distortion peak and the audio clears and is weaker. Many forget that either side of the best audio point is slope detection which is weaker and slightly distorted.

But here, we first need to hear any audio and the home in on it.
I'm with you guys listening in earnest. I will do the tube swapping later this evening as I'm working late today. I have about a dozen 6J6 tubes so I can spend the next 2 days doing tube swaps if that's what's needed. We'll see. I'll update in a few hours. Thanks again so much for the interest and help!
Reply With Quote
  #8  
Old 08-25-2022, 06:51 PM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
Cool. If you have a whole bunch, you'll have a better chance of finding one that works. Of course the tube shield must be on the tube for if it is missing, it too can cause the tuning to be way off.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:42 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.