Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 07-08-2022, 01:14 PM
Chris K Chris K is offline
VideoKarma Member
 
Join Date: Jun 2022
Posts: 1,534
Quote:
Originally Posted by Yamamaya42 View Post
I guess somehow, someway, R185 got mis-connected from the terminal block with r150 and the red wires to the junction of the cans of c127/128 (yel wires) . :O
There may be other lines wrong as well?
Could be and I had a problem with the 40uf C131 electrolytic section. I did a direct replacement but...the positive side of C131A is where the 260V DC from the 5U4 (pin 8) comes off into the system. The 260V is also connected to the positive side of the 40uf section of C128. I have the negative sides of 3 electrolytic sections C128B, C127A and C131A going to the negative side of C128A. The positive of 128A goes to ground. I have a feeling this is where I messed things up. There was no connection between C131A+ and C128B+ so I put a jumper in and the set began to work developing HV and a picture for the first time. But I did do something that wasn't there before Maybe this is where things got messed up. One more question...the 62 ohm field coil. Where is that? Doing the trace, the yellow and black wires seem to go to the speaker! Is that correct??? I didn't touch anything here I swear!!!
Reply With Quote
  #2  
Old 07-08-2022, 01:50 PM
Yamamaya42's Avatar
Yamamaya42 Yamamaya42 is offline
VideoKarma Member
 
Join Date: Nov 2018
Location: Round Rock TX
Posts: 3,253
Quote:
Originally Posted by Chris K View Post
Could be and I had a problem with the 40uf C131 electrolytic section. I did a direct replacement but...the positive side of C131A is where the 260V DC from the 5U4 (pin 8) comes off into the system. The 260V is also connected to the positive side of the 40uf section of C128. I have the negative sides of 3 electrolytic sections C128B, C127A and C131A going to the negative side of C128A. The positive of 128A goes to ground. I have a feeling this is where I messed things up. There was no connection between C131A+ and C128B+ so I put a jumper in and the set began to work developing HV and a picture for the first time. But I did do something that wasn't there before Maybe this is where things got messed up. One more question...the 62 ohm field coil. Where is that? Doing the trace, the yellow and black wires seem to go to the speaker! Is that correct??? I didn't touch anything here I swear!!!
The answer to that is in the parts list.
Speaker 4x6 elliptical E.M. … electromagnetic, there is no perm magnet , it uses a coil. :O
__________________
=^-^=
Yasashii yoru ni hitori utau uta. Asu wa kimi to utaou. Yume no tsubasa ni notte.
いとおしい人のために
Reply With Quote
  #3  
Old 07-08-2022, 02:09 PM
Chris K Chris K is offline
VideoKarma Member
 
Join Date: Jun 2022
Posts: 1,534
Quote:
Originally Posted by Yamamaya42 View Post
The answer to that is in the parts list.
Speaker 4x6 elliptical E.M. … electromagnetic, there is no perm magnet , it uses a coil. :O
Thank you!!!
Reply With Quote
  #4  
Old 07-08-2022, 03:07 PM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
Field coils are typically on speakers. Permanent magnet technology wasn't mature enough until around WWII for permanent magnet speaker magnets to work, so instead electromagnets (field coils) were used. It wasn't until the early 50s that the last makes stopped making field coil speakers.

In the post war era supply shortages made it so some makers used both types depending on what they could get any given week. Case in point I've got a early post war Zenith AA5 table radio/phono that I used to have 3 of. They stamped the chassis for octal tubes, but used the newer style miniature tubes on some sets and the mix of which were octal and mineature varied depending on supply.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:03 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.