Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Rectangular Screen Tube Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 01-17-2022, 05:30 PM
ARC Tech-109 ARC Tech-109 is offline
Retired Batwings Tech
 
Join Date: Jun 2020
Location: Planet Earth
Posts: 612
Alright. I spent some time looking at my Zenith 20YC137 print (sams 932/3) as the YC and the XC are similar enough to where I can fill in the blanks.
The issues you have described so far still point strongly to the IF section and I'm wondering if this this is being caused by a gain issue be it voltages running near the cutoff regions of the IF tubes, misaligned coils or the possibility a 6EH7 is occupying V3.

First lets go back to the voltages but instead of just whats there to ground focus on the differentials as these are far more critical.
V1 with 130v on the plate, 27v on the cathode and 24v on G1 according to the Sams, its this 3V differential between K and G1 that is important.
V2 is a special case in that the cathode is on the end of R51/R52 giving it approx 140v with the grid at 135v, 5v difference here while the plate runs at 230v making the tube run at a potential of 90v. Look for the +245v supply coming into R52 as it will have a dramatic effect on the overall IF performance.Find this source on the half circle terminal of C3 in the power supply section as this is derived from the +340V source thru R202 which is a hefty 15-Watt 720 ohm wirewound resistor, a low +245v source will also pull down the +125v source so don't discount the multi-section capacitor.

Low IF might not kill the sound entirely but it will affect the sync and chroma. Sound & sync are derived prior to the video detector, looking at your YouTube post it appears the sync is trying to latch onto whatever is coming thru V6b which again point me to a gain issue upstream.

The voltages of V4 pin-9 and pin-8 are going to be at or near the supply when the tube is in cutoff, its controlled by the color killer detector and with no colorburst coming into the burst amp the killer detector is not going to provide the needed DC to bias the bandpass amp into conduction. Lets forget about the chroma stages at the moment and focus on the why very little is making its way into pin-2 of V4.

Let me know what you find, I will keep my schematic out and handy
Reply With Quote
  #2  
Old 01-18-2022, 01:35 AM
Jon1967us Jon1967us is offline
VideoKarma Member
 
Join Date: Nov 2018
Posts: 350
Quote:
Originally Posted by ARC Tech-109 View Post
Alright. I spent some time looking at my Zenith 20YC137 print (sams 932/3) as the YC and the XC are similar enough to where I can fill in the blanks.
The issues you have described so far still point strongly to the IF section and I'm wondering if this this is being caused by a gain issue be it voltages running near the cutoff regions of the IF tubes, misaligned coils or the possibility a 6EH7 is occupying V3.

First lets go back to the voltages but instead of just whats there to ground focus on the differentials as these are far more critical.
V1 with 130v on the plate, 27v on the cathode and 24v on G1 according to the Sams, its this 3V differential between K and G1 that is important.
V2 is a special case in that the cathode is on the end of R51/R52 giving it approx 140v with the grid at 135v, 5v difference here while the plate runs at 230v making the tube run at a potential of 90v. Look for the +245v supply coming into R52 as it will have a dramatic effect on the overall IF performance.Find this source on the half circle terminal of C3 in the power supply section as this is derived from the +340V source thru R202 which is a hefty 15-Watt 720 ohm wirewound resistor, a low +245v source will also pull down the +125v source so don't discount the multi-section capacitor.

Low IF might not kill the sound entirely but it will affect the sync and chroma. Sound & sync are derived prior to the video detector, looking at your YouTube post it appears the sync is trying to latch onto whatever is coming thru V6b which again point me to a gain issue upstream.

The voltages of V4 pin-9 and pin-8 are going to be at or near the supply when the tube is in cutoff, its controlled by the color killer detector and with no colorburst coming into the burst amp the killer detector is not going to provide the needed DC to bias the bandpass amp into conduction. Lets forget about the chroma stages at the moment and focus on the why very little is making its way into pin-2 of V4.

Let me know what you find, I will keep my schematic out and handy
Good points to think about for sure. Good to be observant of correct looking differentials. Although, scoping out the IF I'm seeing a pretty healthy signal that seems to hit a wall around V4A. Supposed to have 2.5v, 3, 240 respectively and I have .8, 12, 235, so It's not conducting too well...

Feeding composite straight into the video amp or output yields a pretty good pic, minus of course the sync.

I did replace Q1 with a 2n222 which gave me a little improvement but nothing dramatic. I can make out less faint figures and text in the pic now.

BTW, Peak picture, contrast, brightness, and bright range, all ohm out ok.

I cut the ground on the delay line and jumpered it with no improvement.

Will continue analyzing and report back any interesting findings.

Waiting on tubes for subbing, as well.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:09 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.