Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 12-23-2021, 02:39 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by vortalexfan View Post
Well that capacitor though is where my voltages to the audio output circuit are getting lost though for sure because I measured the B+ voltage from the terminal that C49 ties to and goes to ground and I have B+ voltage there going to ground but then when I measure from that point to the other side of C50 the 10,000 pF ceramic disc cap there's no voltage there (it's -20V or so) and that is supposed to supply the voltages to pins 5 and 6 of the 6AQ5 tube, and yes I did replace C50 with a new capacitor finally and that didn't change the voltage readings any.
Let's get one thing straight here. B+ is not suppose to get to pins 5 and 6 of the 6AQ5 through C50. C50 is a audio signal coupling cap to the top of the volume control. C50's function is to pass the audio signal from the plate of the detector to the audio output grid. A capacitor is used because it's intended to block the B+ feeding the plate of the detector tube from getting into the grid circuit of the 6AQ5.
Reply With Quote
  #2  
Old 12-23-2021, 02:48 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by Kevin Kuehn View Post
Let's get one thing straight here. B+ is not suppose to get to pins 5 and 6 of the 6AQ5 through C50. C50 is a audio signal coupling cap to the top of the volume control. C50's function is to pass the audio signal from the plate of the detector to the audio output grid. A capacitor is used because it's intended to block the B+ feeding the plate of the detector tube from getting into the grid circuit of the 6AQ5.
Well either way I'm not getting any audio out of the TV and I'm still not getting the 200+ volts I need to be getting on pins 5 and 6 of the 6AQ5 tube that the Sam's calls out and I'm not getting 17V on pin 2 of the 6AQ5 either, so I'm still stumped as to what's going on with the audio section of this TV, and I've still got no signal from the tuner to the TV on here either.

Last edited by vortalexfan; 12-23-2021 at 04:06 PM.
Reply With Quote
  #3  
Old 12-23-2021, 04:43 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by vortalexfan View Post
Well either way I'm not getting any audio out of the TV and I'm still not getting the 200+ volts I need to be getting on pins 5 and 6 of the 6AQ5 tube that the Sam's calls out and I'm not getting 17V on pin 2 of the 6AQ5 either, so I'm still stumped as to what's going on with the audio section of this TV, and I've still got no signal from the tuner to the TV on here either.

Reread post #245 where you had 210v at C3B. You need to follow that point to pins 5 and 6 of your 6AQ5 and see where you loose the 210V. Follow the schematic and ohm everything out. One path is from C3B positive to pin 6(screen), the other is C3B positive to the bottom(red) wire of the output transformer primary. B+ needs to go in on the red wire of the primary winding and exit on the blue wire to pin 5(plate) of the 6AQ5. If there's no connections where there should be, something has become open or otherwise mis-wired.


Quote:
Originally Posted by old_coot88 View Post
OK. That's close enough for now. At least you've verified B+ on C3b.

The identical voltage should be appearing on pin 6 (screen grid) of the 5AQ5, and on the bottom of the output xfmr primary (red lead).

In other words, there should be solid continuity (zero ohms) twixt all those points. (Forget the negative voltage issue for now) Main thing is to find out what connection's gone open.

With the set OFF, and an ohmmeter set to RX1, connect the black lead to pin 6. With the other lead, check for zero ohms to bottom of xfmr primary (red lead), and to C3b. You'll probably find the connection to C3b is what's open.

BTW, also check the xfmr primary for a few hundred ohms between pins 6 and 5 (plate) of the 5AQ5.

Once this is all sorted out, check for solid continuity (zero ohms) from C3's can to ground. Any resistance here could be contributing to the 'negative voltage' condition.
[Edit] Here's a picture of the bottom side of my working chassis showing the 5AQ5(6AQ5) connections so you can compare your wiring.


Last edited by Kevin Kuehn; 12-23-2021 at 05:45 PM.
Reply With Quote
  #4  
Old 12-23-2021, 07:02 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by Kevin Kuehn View Post
Reread post #245 where you had 210v at C3B. You need to follow that point to pins 5 and 6 of your 6AQ5 and see where you loose the 210V. Follow the schematic and ohm everything out. One path is from C3B positive to pin 6(screen), the other is C3B positive to the bottom(red) wire of the output transformer primary. B+ needs to go in on the red wire of the primary winding and exit on the blue wire to pin 5(plate) of the 6AQ5. If there's no connections where there should be, something has become open or otherwise mis-wired.




[Edit] Here's a picture of the bottom side of my working chassis showing the 5AQ5(6AQ5) connections so you can compare your wiring.

Well besides the fact that your TV's wiring is in much better shape than mine is (the color is faded from my TV's wiring) I don't see anything different from yours and mine except that it seems you still kept some of the original can caps in circuit whereas mine are all replacent capacitors.

I really don't know what's going here.
Reply With Quote
  #5  
Old 12-23-2021, 08:12 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by vortalexfan View Post
Well besides the fact that your TV's wiring is in much better shape than mine is (the color is faded from my TV's wiring) I don't see anything different from yours and mine except that it seems you still kept some of the original can caps in circuit whereas mine are all replacent capacitors.

I really don't know what's going here.
I sawed the top off my cans and re-used the old terminals. Any chance you can post a close up of the underside of your chassis around the 6AQ5, including your filter caps? Sometimes it helps to have a fresh set of eye's look things over.

Reply With Quote
Audiokarma
  #6  
Old 12-23-2021, 08:34 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by Kevin Kuehn View Post
I sawed the top off my cans and re-used the old terminals. Any chance you can post a close up of the underside of your chassis around the 6AQ5, including your filter caps? Sometimes it helps to have a fresh set of eye's look things over.

Ok, I wondered about that. I'll get you a picture of my 5 (6)AQ5 tube section of the TV and the replacement electrolytics.
Reply With Quote
  #7  
Old 12-24-2021, 12:05 PM
dieseljeep dieseljeep is offline
VideoKarma Member
 
Join Date: Jul 2010
Posts: 7,562
Quote:
Originally Posted by Kevin Kuehn View Post
I sawed the top off my cans and re-used the old terminals. Any chance you can post a close up of the underside of your chassis around the 6AQ5, including your filter caps? Sometimes it helps to have a fresh set of eye's look things over.

Rather impressive! How do you cut the cans so perfect?
Bought and sold a set like that about 60 years ago. Mine was an earlier model that used a 3BY6 instead of the better circuit using a 3BU8.
The outward appearance was similar.
Reply With Quote
  #8  
Old 12-24-2021, 12:21 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by dieseljeep View Post
Rather impressive! How do you cut the cans so perfect?
Bought and sold a set like that about 60 years ago. Mine was an earlier model that used a 3BY6 instead of the better circuit using a 3BU8.
The outward appearance was similar.
Thanks. I actually removed these and used my band saw. Then a few passes over 220 grit on a flat surface squares the end. Seems like a lot of work, but by using a very large (radiator sized ) soldering iron I'm able to heat the ground lugs and squeeze them straight with a flat nose pliers, then carefully wiggle them free. Space permitting you certainly could hack them off using a Zona saw while they're still attached to a chassis.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:15 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.