Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 12-07-2021, 06:08 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by Kevin Kuehn View Post
I've got a couple dumb questions.

What DC voltage do measure from end to end of the 470 ohm R56?

And from what point have you been getting your B- or ground reference when taking DC voltage measurements? The reason I ask is that you're 245 B+ measured about 25 volts low, and also you mentioned measuring -22 volts at some point.
This may sound weird but now suddenly I'm getting 210V before and after R56, and R56 is not getting hot to the touch, but I'm still getting the weird voltage readings after C50 though, and still getting low voltage readings at pins 5 and 6 of the 5AQ5 tube socket.

I removed the output transformer completely from the circuit and took voltage readings and I'm getting 0V now at pins 1 and 7 of the 5AQ5 tube socket and pin 2 around 5V on the cathode and and still getting 22V on pins 5 and 6 of the 5AQ5 tube socket.

The -22V figure came in because of the fact that for some reason or another when I take voltage measurements on anything after C50 all the voltages are negative unless I flip my probes so that I use my positive probe as the negative probe and the negative probe as my positve probe and then I get positive voltage readings, and my reference to ground is the chassis because that's what its supposed to be according to the schematic.
Reply With Quote
  #2  
Old 12-07-2021, 07:21 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by vortalexfan View Post
This may sound weird but now suddenly I'm getting 210V before and after R56, and R56 is not getting hot to the touch, but I'm still getting the weird voltage readings after C50 though, and still getting low voltage readings at pins 5 and 6 of the 5AQ5 tube socket.

I removed the output transformer completely from the circuit and took voltage readings and I'm getting 0V now at pins 1 and 7 of the 5AQ5 tube socket and pin 2 around 5V on the cathode and and still getting 22V on pins 5 and 6 of the 5AQ5 tube socket.

The -22V figure came in because of the fact that for some reason or another when I take voltage measurements on anything after C50 all the voltages are negative unless I flip my probes so that I use my positive probe as the negative probe and the negative probe as my positive probe and then I get positive voltage readings, and my reference to ground is the chassis because that's what its supposed to be according to the schematic.
You really don't want to run the set with the output transformer removed other than to take quick measurements because the 5AQ5 screen grid(pin 6) is still getting B+ and it's not healthy for the tube without the plate also getting B+. I really can't follow what you mean when you say everything after C50 is negative? Exactly where are you measuring negative voltage in respect to B- ?

I'd like to suggest we focus only on this little section instead of jumping all over the map. C50 is only a audio coupling cap that passes audio from the detector stage to the volume control, so we're really not worried about anything other than this little portion of the schematic. Once we figure out what's ailing the audio output then we can move onto the bigger picture.


Last edited by Kevin Kuehn; 12-07-2021 at 07:43 PM.
Reply With Quote
  #3  
Old 12-07-2021, 10:35 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
For our OP I sketched over the schematic using conventional current the direction DC flows from B+ through the circuit and returns to ground. The 5AQ5 being self (cathode) biased sets the tubes quiescent current. Under normal operation there should be no DC flowing in the volume control or grid circuit. C50 is the grid coupling cap that's purpose it to isolate the 5AQ5 grid from the preceding plate circuit's DC. C51 basically damps out very high frequencies in the output trans primary. It's this flow of quiescent DC current that produces the appropriate voltage drops across the resistance or impedance of the various components. Healthy capacitors should not pass DC therefore would not change this quiescent or idling current in the circuit. You could remove C50 and 51 and the circuit should still work completely isolated from the rest the TV. Normally if you touch a screwdriver or finger to the grid or volume control it will produce a buzz in the speaker. Anyhow I though it might help remove some of the mystery surrounding how this little section of the TV works. Once you understand what's suppose to happen it sometimes helps to find the source of trouble.

Reply With Quote
  #4  
Old 12-08-2021, 01:18 AM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by Kevin Kuehn View Post
You really don't want to run the set with the output transformer removed other than to take quick measurements because the 5AQ5 screen grid(pin 6) is still getting B+ and it's not healthy for the tube without the plate also getting B+. I really can't follow what you mean when you say everything after C50 is negative? Exactly where are you measuring negative voltage in respect to B- ?

I'd like to suggest we focus only on this little section instead of jumping all over the map. C50 is only a audio coupling cap that passes audio from the detector stage to the volume control, so we're really not worried about anything other than this little portion of the schematic. Once we figure out what's ailing the audio output then we can move onto the bigger picture.


OK so what I mean by the voltages after C50 are all Negative is that part of the B+ (245V supply) line goes into TS8-4 which is also where one side of C50 goes in at as well as R54 and R56 and C3B tie in at, and at TS8-3 which is where the other side of C50 comes out (and also where the other side of the 245V supply comes out to supply the 5AQ5 tube with its necessary voltages) is where all of the voltages end up measuring negative, as for my B- reference its where the black wire coming from the power switch ties to the chassis and to the "chassis ground" for the old C3 can (which is out of circuit), and using that B- reference point is giving me negative voltage readings on the TS8-3 side of C50/245V supply line unless I reverse my probes (positive red probe to B- reference and the black negative probe to the voltage reference point).

Now I don't know how I can make that any clearer than that but I'm telling you that's what's happening to me with this TV.
Reply With Quote
  #5  
Old 12-08-2021, 01:52 AM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
I don't know how you could of missed this, but C50 has a lot more to do with the audio output circuit than you think it does, for example the 245V B+ supply is shared in common between the Audio Detector Tube and the Audio Output tube, and both supplies are filtered through C3B which are their common tie point in the 245V B+ supply through R54 and R56 (R54 feeds the 245V B+ supply line to the Detector Tube and R56 feeds the 245V B+ supply to the output tube and both of those resistors are tied to the positive side of C3B which is tied to chassis ground just like it was originally when it was in the old can cap, if you look at my schematic excerpt and my markings explaining where the negative voltages are being measured at and where the common points are in the two "unrelated circuits" you'll see that I'm not nuts in how I'm following this circuit layout and what I mean by the voltages after C50 are negative unless I reverse my leads.
Attached Images
File Type: jpg Zenith Bugeye TV Audio Section Schematic.jpg (127.9 KB, 11 views)
Reply With Quote
Audiokarma
  #6  
Old 12-08-2021, 02:09 AM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by vortalexfan View Post
I don't know how you could of missed this, but C50 has a lot more to do with the audio output circuit than you think it does, for example the 245V B+ supply is shared in common between the Audio Detector Tube and the Audio Output tube, and both supplies are filtered through C3B which are their common tie point in the 245V B+ supply through R54 and R56 (R54 feeds the 245V B+ supply line to the Detector Tube and R56 feeds the 245V B+ supply to the output tube and both of those resistors are tied to the positive side of C3B which is tied to chassis ground just like it was originally when it was in the old can cap, if you look at my schematic excerpt and my markings explaining where the negative voltages are being measured at and where the common points are in the two "unrelated circuits" you'll see that I'm not nuts in how I'm following this circuit layout and what I mean by the voltages after C50 are negative unless I reverse my leads.
I'm well aware B+ feeds multiple circuits. Are you saying you are measuring a negative voltage at point TS8-3 where you have circled, or everything to the right of that point including all the audio output voltages? C50 is an audio coupling cap and has absolutely no influence on B+, other than it could be leaky and letting B+ cross over to the volume control. If that cap is bothering you please remove it from the circuit.

Last edited by Kevin Kuehn; 12-08-2021 at 02:14 AM.
Reply With Quote
  #7  
Old 12-08-2021, 02:32 AM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by Kevin Kuehn View Post
I'm well aware B+ feeds multiple circuits. Are you saying you are measuring a negative voltage at point TS8-3 where you have circled, or everything to the right of that point including all the audio output voltages? C50 is an audio coupling cap and has absolutely no influence on B+, other than it could be leaky and letting B+ cross over to the volume control. If that cap is bothering you please remove it from the circuit.
I'm measuring a negative voltage at point TS8-3 and everything to the right of that in the TV's Audio Circuit, everything to the left of that measures normally (or as normally as a still malfunctioning TV can measure) which is the 210V that is supposed to be the 245V B+ Supply which is currently only measuring 210V right now.
Reply With Quote
  #8  
Old 12-08-2021, 02:36 AM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by vortalexfan View Post
I'm measuring a negative voltage at point TS8-3 and everything to the right of that in the TV's Audio Circuit, everything to the left of that measures normally (or as normally as a still malfunctioning TV can measure) which is the 210V that is supposed to be the 245V B+ Supply which is currently only measuring 210V right now.
How about you disconnect C50 and see if that negative voltage situation changes. I'm trying to get you to isolate one circuit from the other so we can make some progress and you're being very difficult to influence.
Reply With Quote
  #9  
Old 12-08-2021, 02:01 AM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by vortalexfan View Post
OK so what I mean by the voltages after C50 are all Negative is that part of the B+ (245V supply) line goes into TS8-4 which is also where one side of C50 goes in at as well as R54 and R56 and C3B tie in at, and at TS8-3 which is where the other side of C50 comes out (and also where the other side of the 245V supply comes out to supply the 5AQ5 tube with its necessary voltages) is where all of the voltages end up measuring negative, as for my B- reference its where the black wire coming from the power switch ties to the chassis and to the "chassis ground" for the old C3 can (which is out of circuit), and using that B- reference point is giving me negative voltage readings on the TS8-3 side of C50/245V supply line unless I reverse my probes (positive red probe to B- reference and the black negative probe to the voltage reference point).

Now I don't know how I can make that any clearer than that but I'm telling you that's what's happening to me with this TV.
Is the bottom side of R54 on your TV connected directly to the left end of R56, or is it connecting to the alternate point Sams shows with the dotted line? If you'll notice there's an X in the B+ line between R56 and R54. That X indicates the B+ point from R56 is disconnected from R54 when the alternate source is used. In any event you're no longer focusing on the audio output issue and the point feeding R54 has no influence on the audio output portion.
Reply With Quote
  #10  
Old 12-08-2021, 02:41 AM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by Kevin Kuehn View Post
Is the bottom side of R54 on your TV connected directly to the left end of R56, or is it connecting to the alternate point Sams shows with the dotted line? If you'll notice there's an X in the B+ line between R56 and R54. That X indicates the B+ point from R56 is disconnected from R54 when the alternate source is used. In any event you're no longer focusing on the audio output issue and the point feeding R54 has no influence on the audio output portion.
The top-side of R56 is connected to the bottom side of R54 which is connected across C3B, which is the point where you were saying that there was a "dead short" earlier when I was telling you that the voltage from there was going from 145V to 22V at pins 5 and 6 on the 5AQ5 tube socket, which by the way, that is how the original C3B in the can was hooked up from the factory, unless you're trying to suggest that somehow this TV was miswired from the factory and somehow managed to get past Zenith's stringent QC standards?
Reply With Quote
Audiokarma
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:07 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.