Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 12-07-2021, 03:25 AM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by Kevin Kuehn View Post
Your ESR meter isn't of much use in this situation. Did you lift one lead and see if your B+ rises?
No I haven't yet, I'll do it when I get up, I'm going to bed because I'm getting tired.

Should I lift the negative or the positive side of the capacitor?
Reply With Quote
  #2  
Old 12-07-2021, 03:29 AM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by vortalexfan View Post
No I haven't yet, I'll do it when I get up, I'm going to bed because I'm getting tired.

Should I lift the negative or the positive side of the capacitor?
Depends on if your an optimist or pessimist.
Reply With Quote
  #3  
Old 12-07-2021, 01:25 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
OK so, R54 which is a 390k Ohm 1/2W 10% resistor is measuring 470k Ohms which is way out of tolerance would that cause some issues in the circuit?
Reply With Quote
  #4  
Old 12-07-2021, 01:41 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by vortalexfan View Post
OK so, R54 which is a 390k Ohm 1/2W 10% resistor is measuring 470k Ohms which is way out of tolerance would that cause some issues in the circuit?
You'd get a little lower plate voltage on V7, but that surly has nothing to do with your high current draw situation. Am I safe in assuming R56 gets blistering hot whenever you power the set on? Have you disconnected one end of C3-B?
Reply With Quote
  #5  
Old 12-07-2021, 02:11 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by Kevin Kuehn View Post
You'd get a little lower plate voltage on V7, but that surly has nothing to do with your high current draw situation. Am I safe in assuming R56 gets blistering hot whenever you power the set on? Have you disconnected one end of C3-B?
I have but that capacitor has R54 and R56 attached across the positive side of C3B and so disconnecting the positive side of C3B from the circuit just leaves R54 and R56 tied together which would most certainly cause some issues in the TV.
Reply With Quote
Audiokarma
  #6  
Old 12-07-2021, 02:34 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
OK so I powered up the TV with R54 and R56 tied together and C3B out of the picture and the voltage went up to 145V (still down a bit from where it should be but not as much, the voltage I think is still getting lost after C50 somehow because the voltage before C50 is 145V and after C50 its becomes a negative voltage that is in the 10v range, and then from there the voltages at pins 5 and 6 of the 5BQ5 output tube become basically non-existant.
Reply With Quote
  #7  
Old 12-07-2021, 02:57 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
OK so I put C3B back into the circuit and the voltage is still around 145V upto C50 then after C50 the voltage drops off to basically nothing, so I'm suspecting C50 and C51 are both defective which is why the voltage is non-existant at p5 and p6 of the 5BQ5 tube socket.
Reply With Quote
  #8  
Old 12-07-2021, 03:03 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by vortalexfan View Post
OK so I powered up the TV with R54 and R56 tied together and C3B out of the picture and the voltage went up to 145V (still down a bit from where it should be but not as much, the voltage I think is still getting lost after C50 somehow because the voltage before C50 is 145V and after C50 its becomes a negative voltage that is in the 10v range, and then from there the voltages at pins 5 and 6 of the 5BQ5 output tube become basically non-existant.
Unfortunately I can't follow what you're doing there. R54 being 390k cannot pass the kind current that you have being drawn through the 475 ohm( R56). The fact that B+ came up that much when you disconnected C3B is a strong clue you'll find more of your issue very close to that same area. Is R56 still in fact measuring 470 ohms, or has it been overheated and drifted much higher? You may get another clue if you temporarily disconnect either the blue or red leads of the output transformer, one lead at a time, while monitoring the voltage at the left end of R56. Once all loads are disconnected B+ should measure the same between both ends of R56 to ground. No load equals no voltage drop, so your goal here is disconnecting current paths until you find where the higher than normal draw is coming from. When you say you have no voltage on pins 5 or 6 of the 5BQ5 that strongly indicates a short some place before those points.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:53 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.