Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Flat Panels & Digital Format

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 04-07-2021, 10:42 PM
YamahaFreak's Avatar
YamahaFreak YamahaFreak is offline
<-- CSXT 6038, EMD GP40-2
 
Join Date: Dec 2005
Location: TOO sunny Florida, USA
Posts: 580
Quote:
Originally Posted by JohnCT View Post
What are you VS and VA voltages, and if they appear, do they stay on or do they decay after a few seconds?

John
John, thanks for reminding me. Can you refresh my memory as to how to properly take these voltages? I assume there are VS and VA test points, and the negative probe goes somewhere on chassis ground, such as the TV frame. I want to make sure I don't fry the TV, my meter, or myself!
__________________
Sony Trinitron Fan
Reply With Quote
  #2  
Old 04-08-2021, 06:55 AM
JohnCT's Avatar
JohnCT JohnCT is offline
VideoKarma Member
 
Join Date: Jan 2020
Posts: 749
Quote:
Originally Posted by YamahaFreak View Post
John, thanks for reminding me. Can you refresh my memory as to how to properly take these voltages? I assume there are VS and VA test points, and the negative probe goes somewhere on chassis ground, such as the TV frame. I want to make sure I don't fry the TV, my meter, or myself!
You won't damage your meter no matter what you do. The highest voltages on a plasma are below 400V under any condition.

On the power supply, there are test points marked for the VS and VA, which are developed on that board. There are also other voltages that are generated on the sustain boards, but that's farther down the road.

If there are no test points, then use the large harness connectors. The VS will usually have two to four pins all paralleled for current capability and the VA one or two, but the boards are marked for these voltages right at the connector.

For either voltage, you use cold ground as reference, which would be any of the mounting screws (other than upper and lower buffer board mounting screws which might be above ground) or even the entire back side of the plasma display itself.

Other voltages on the sustain boards can be referenced to cold ground or depending on maker, there might be two test points printed on the board to check those voltages.

But for now, our first attack is to see if the power supply is working, so the VS and VA voltages are the first step.

John
Reply With Quote
  #3  
Old 04-13-2021, 12:38 AM
YamahaFreak's Avatar
YamahaFreak YamahaFreak is offline
<-- CSXT 6038, EMD GP40-2
 
Join Date: Dec 2005
Location: TOO sunny Florida, USA
Posts: 580
Quote:
Originally Posted by JohnCT View Post
You won't damage your meter no matter what you do. The highest voltages on a plasma are below 400V under any condition.

On the power supply, there are test points marked for the VS and VA, which are developed on that board. There are also other voltages that are generated on the sustain boards, but that's farther down the road.

If there are no test points, then use the large harness connectors. The VS will usually have two to four pins all paralleled for current capability and the VA one or two, but the boards are marked for these voltages right at the connector.

For either voltage, you use cold ground as reference, which would be any of the mounting screws (other than upper and lower buffer board mounting screws which might be above ground) or even the entire back side of the plasma display itself.

Other voltages on the sustain boards can be referenced to cold ground or depending on maker, there might be two test points printed on the board to check those voltages.

But for now, our first attack is to see if the power supply is working, so the VS and VA voltages are the first step.

John
Hi again John,

I found the measurement process straightforward. Here is what I found.

VS voltage marked on the panel is 208 volts. I measured a high of 463 volts at startup, then it steadily dropped until stabilizing at 23 volts.

VA voltage marked on the panel is 57 volts. I measured a high of 126 volts at startup, dropping to zero after several seconds.

I repeated the measurements a few times...always the same. This, to me, suggests there is a power supply issue.
__________________
Sony Trinitron Fan
Reply With Quote
  #4  
Old 04-13-2021, 05:00 PM
JohnCT's Avatar
JohnCT JohnCT is offline
VideoKarma Member
 
Join Date: Jan 2020
Posts: 749
Quote:
Originally Posted by YamahaFreak View Post
Hi again John,

I found the measurement process straightforward. Here is what I found.

VS voltage marked on the panel is 208 volts. I measured a high of 463 volts at startup, then it steadily dropped until stabilizing at 23 volts.

VA voltage marked on the panel is 57 volts. I measured a high of 126 volts at startup, dropping to zero after several seconds.

I repeated the measurements a few times...always the same. This, to me, suggests there is a power supply issue.
Holy crap, I've never seen one do that. Are you sure about your meter and using the power supply ground screws for ground? These have a hot and cold side so if you're using the heatsinks as ground, be aware that there are one or more on the hot side.

Even when I've seen them overshoot, it's never been more than a few volts as the power supply is very good about watching for overvoltage and snuffing them out quickly.

Also, most VA and VS supplies are separate from each other, so it seems extraordinarily odd that both would not only overshoot, but by so much.

Please don't take this the wrong way, but see if you can verify your meter.

I'll see if I have a power supply for that in the shop. Is there a BN44 number on it?

John
Reply With Quote
  #5  
Old 04-13-2021, 08:49 PM
YamahaFreak's Avatar
YamahaFreak YamahaFreak is offline
<-- CSXT 6038, EMD GP40-2
 
Join Date: Dec 2005
Location: TOO sunny Florida, USA
Posts: 580
Quote:
Originally Posted by JohnCT View Post
Holy crap, I've never seen one do that. Are you sure about your meter and using the power supply ground screws for ground? These have a hot and cold side so if you're using the heatsinks as ground, be aware that there are one or more on the hot side.

Even when I've seen them overshoot, it's never been more than a few volts as the power supply is very good about watching for overvoltage and snuffing them out quickly.

Also, most VA and VS supplies are separate from each other, so it seems extraordinarily odd that both would not only overshoot, but by so much.

Please don't take this the wrong way, but see if you can verify your meter.

I'll see if I have a power supply for that in the shop. Is there a BN44 number on it?

John
John, would a low battery in the meter affect its readings? It hasn't ever given me grossly wrong readings before. I am using the wall mounting screw holes for ground. I assume I'm supposed to be using the AC setting, not DC. I will get the part number off the board tomorrow when I open the TV up again. Thanks for your guidance so far.
__________________
Sony Trinitron Fan
Reply With Quote
Audiokarma
  #6  
Old 04-14-2021, 06:18 AM
JohnCT's Avatar
JohnCT JohnCT is offline
VideoKarma Member
 
Join Date: Jan 2020
Posts: 749
Quote:
Originally Posted by YamahaFreak View Post
John, would a low battery in the meter affect its readings? It hasn't ever given me grossly wrong readings before. I am using the wall mounting screw holes for ground. I assume I'm supposed to be using the AC setting, not DC. I will get the part number off the board tomorrow when I open the TV up again. Thanks for your guidance so far.
The wall mounting holes are fine for ground when reading any secondary supply voltage from the power board, but you are measuring DC, not AC.

Even so, those supplies are well bypassed and I'm surprised your meter is giving you those readings on the AC scale. What kind of meter is it?

If your meter has a min/max feature, preset the range for higher voltage and record the max voltage for the VS and VA.

If it doesn't have the min/max, just read the highest value you see before it shuts down.

John
Reply With Quote
  #7  
Old 04-14-2021, 03:01 PM
YamahaFreak's Avatar
YamahaFreak YamahaFreak is offline
<-- CSXT 6038, EMD GP40-2
 
Join Date: Dec 2005
Location: TOO sunny Florida, USA
Posts: 580
Quote:
Originally Posted by JohnCT View Post
The wall mounting holes are fine for ground when reading any secondary supply voltage from the power board, but you are measuring DC, not AC.

Even so, those supplies are well bypassed and I'm surprised your meter is giving you those readings on the AC scale. What kind of meter is it?

If your meter has a min/max feature, preset the range for higher voltage and record the max voltage for the VS and VA.

If it doesn't have the min/max, just read the highest value you see before it shuts down.

John
John,

Right, will switch to DC readings. The meter has no min/max function, as it's just a cheapie from Harbor Freight. It's all I have. I will open the set again tonight and get updated readings for you.
__________________
Sony Trinitron Fan
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:07 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.