Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Recorded Video

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 03-14-2021, 08:30 AM
JohnCT's Avatar
JohnCT JohnCT is offline
VideoKarma Member
 
Join Date: Jan 2020
Posts: 749
Quote:
Originally Posted by ThePlague View Post
Is it possible that without the counter belt attached, the system is not producing audio?
I never say never as I've seen stuff in my 50 years in this business that would appear to make no sense.

Most of the time, a bad counter belt would cause (other than no counter movement) a shutdown in a few seconds as most of the counters had a hall effect sensor to inform the micro of tape movement, but of course, not all did.

Now, that machine looks suspiciously like the RCA convertible VFP series. We did have an audio problem with the RCA convertibles, and there are two tiny relays that can cause either noisy audio or no audio. I think they were identified as R400 or R1400 or so - maybe R1400 and R1401. See if there's any on the board marked something like that.

If that's your problem, there's a *small* chance I may have a couple in an RCA box.


John
Reply With Quote
  #2  
Old 03-15-2021, 08:01 PM
ThePlague ThePlague is offline
VideoKarma Member
 
Join Date: Apr 2017
Location: Denver, Colorado
Posts: 71
Quote:
Originally Posted by Electronic M View Post
I don't think that's your problem.

The audio recording bias Oscillator is only supposed to run while recording. That osc runs at above audible frequencies to facilitate correctly magnetizing the tape during recording...If you run the record osc during playback it may damage the existing recording.

If you can identify the audio playback head (its often clustered with the tracking control track head) you could try injecting low-level audio there and see if it makes it through.
Some decks especially mid-80's and older had long multi-pole switches on the PCBs that look like those found in 70's and 80's cassette decks. Those PCB switches have to connect into the mechanism correctly to play properly....Case in point I worked on a sony SL-5800 Beta deck where the bottom PCB had such switches and if the bottom PBC was hinged down into service mode (which I needed to do) the switch on the PCB that switched audio from tuner to tape would not be engaged by the mech and stay in tuner mode (I could manually toggle it).

Not familiar with your model so I can't offer much more insight.
No large multi-pole switches on this unfortunately. All soft touch logic. As much as I enjoy this portable systems, the weird design choices made to build to a size always incur the strangest servicing quirks. I will go ahead and try and see if there is an audio signal coming off of the audio playback head to verify the audio board is actually getting a signal.


Quote:
Originally Posted by JohnCT View Post
I never say never as I've seen stuff in my 50 years in this business that would appear to make no sense.

Most of the time, a bad counter belt would cause (other than no counter movement) a shutdown in a few seconds as most of the counters had a hall effect sensor to inform the micro of tape movement, but of course, not all did.

Now, that machine looks suspiciously like the RCA convertible VFP series. We did have an audio problem with the RCA convertibles, and there are two tiny relays that can cause either noisy audio or no audio. I think they were identified as R400 or R1400 or so - maybe R1400 and R1401. See if there's any on the board marked something like that.

If that's your problem, there's a *small* chance I may have a couple in an RCA box.


John
This unit seems to have the hall effect sensor on the pulley attached to the take up reel instead of on the counter side pulley itself. Lets the unit play without having a working counter I suppose.

Looking at the audio board in the unit and the schematic, it would seem that you are correct. There are two small relays labeled RL402 and RL401. I am not sure if these would produce an audible click, but I do not here any actuation noise. When I get the chance I will try and test these out.

If you do happen to have a couple, I would be more than happy to pay you for them. Even if it isn't the issue, it would be nice to have a spare set.
Reply With Quote
  #3  
Old 03-16-2021, 03:04 PM
Ed in Tx's Avatar
Ed in Tx Ed in Tx is offline
Zenith Walton My 1st TV
 
Join Date: Nov 2008
Location: DFW
Posts: 1,421
Quote:
Originally Posted by ThePlague View Post

Looking at the audio board in the unit and the schematic, it would seem that you are correct. There are two small relays labeled RL402 and RL401....
While playing back a tape try tapping on the relays with a toothbrush handle or small screwdriver handle. You may hear a change or even proper audio.

I've cleaned and made relays work at least temporarily with a piece of thick paper wet with Deoxit spray back and forth a few times between the contacts.
Reply With Quote
  #4  
Old 04-24-2021, 11:48 AM
ThePlague ThePlague is offline
VideoKarma Member
 
Join Date: Apr 2017
Location: Denver, Colorado
Posts: 71
Quote:
Originally Posted by Ed in Tx View Post
While playing back a tape try tapping on the relays with a toothbrush handle or small screwdriver handle. You may hear a change or even proper audio.

I've cleaned and made relays work at least temporarily with a piece of thick paper wet with Deoxit spray back and forth a few times between the contacts.
Sorry for the delay in my response. Finally have some hours to put into to troubleshooting this deck. I was able to check the relays, and they are clicking away. My next idea is check the output of the audio head and if that is good, try and trace out the playback audio path from the audio circuit diagram. I will report back.
Reply With Quote
  #5  
Old 04-24-2021, 12:13 PM
Ed in Tx's Avatar
Ed in Tx Ed in Tx is offline
Zenith Walton My 1st TV
 
Join Date: Nov 2008
Location: DFW
Posts: 1,421
Just because a relay "clicks" doesn't mean the contacts are making good electrical contact.
Reply With Quote
Audiokarma
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:03 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.