Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Transistor Portable Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 01-08-2021, 06:15 PM
JohnCT's Avatar
JohnCT JohnCT is offline
VideoKarma Member
 
Join Date: Jan 2020
Posts: 749
Quote:
Originally Posted by PortableTV View Post
I have been picking up more and more of these Casio TV's and a bunch have the dead green screen.

This one I watched happen. I put batteries in it and it held the picture I had broadcast to it from my Blonder Tongue for about 30 seconds and then slowly went green.

Is this a capacitor issue? Any guidance would be helpful!


Generally, electrolytic capacitor symptoms dictate that the problem improves with running, not get worse. The exception are what we in the camcorder repair business used to call "fish" caps, because they stunk like low tide when they were powered up. They ooze their electrolyte out of the bottom and become conductive as they rehydrate any crap that was under or near the cap.

Open it up, exhale, and take a deep breath. If the board smells like your cat after it eats, you will need a wholesale swap of every cap on the board most likely.

We used to do tons of 8mm and mini DV (mostly Sony) that needed dozens of these changed on a board the size of a deck of cards.

John
Reply With Quote
  #2  
Old 01-08-2021, 07:39 PM
PortableTV PortableTV is offline
VideoKarma Member
 
Join Date: Dec 2020
Posts: 13
Quote:
Originally Posted by JohnCT View Post
Open it up, exhale, and take a deep breath. If the board smells like your cat after it eats, you will need a wholesale swap of every cap on the board most likely.

We used to do tons of 8mm and mini DV (mostly Sony) that needed dozens of these changed on a board the size of a deck of cards.

John
I opened it up. No discernable smell.

There's only 4 caps on the back of the screen, 2 are larger SMD's so at least I can change them. Fingers crossed that that's the fix. The main board has a bunch of regular caps but almost a dozen tiny SMD's that I would have zero idea how to go about changing.

I guess we'll see...
Reply With Quote
  #3  
Old 01-09-2021, 02:59 PM
JohnCT's Avatar
JohnCT JohnCT is offline
VideoKarma Member
 
Join Date: Jan 2020
Posts: 749
Quote:
Originally Posted by PortableTV View Post
I opened it up. No discernable smell.

There's only 4 caps on the back of the screen, 2 are larger SMD's so at least I can change them. Fingers crossed that that's the fix. The main board has a bunch of regular caps but almost a dozen tiny SMD's that I would have zero idea how to go about changing.

I guess we'll see...
If there's no smell, it might respond to heat. *Gently* warm the boards with a hair dryer and try again. If it produces a picture, the easiest way to find the offending cap(s) is with a scope. Most of those caps are bypass, so there will be no signal on the neg side (assuming common ground) and very little signal on the pos side. Most caps should have about the same amount of "hash" on them. If you find a cap with a double or more the amount of noise on the pos side that the others do, the cap is prob bad.

Before you change it, make sure it's not a coupling cap where the same signal would be on both sides of the cap, so move the scope to the neg side. If there's no signal there, it's a bypass and prob bad.

John
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:10 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.