Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early Color Television

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 09-11-2020, 10:52 AM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
I haven't had to do this with a 15G socket yet (knock on wood) but I believe they are riveted together the same way 21" color sockets are riveted. I've had to deal with 21" sockets where the wires broke off inside the base. What I did was drill out the rivets(if the heads are not sunken grinding is a good option), carefully open the socket to avoid mixing up the wires, resolder the wire that broke and clean and tighten the worst contacts, then reassemble using nuts and machine screws the same diameter as the rivets. Not the simplest process but a little easier than connecting ~12 wires for a new socket.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4

Last edited by Electronic M; 09-11-2020 at 10:56 AM.
Reply With Quote
  #2  
Old 09-12-2020, 12:37 AM
ohohyodafarted's Avatar
ohohyodafarted ohohyodafarted is offline
Bob Galanter
 
Join Date: Sep 2005
Location: Whitefish Bay, Wi (Milwaukee)
Posts: 1,080
I my memory serves me those are not rivets. They are actually long helix spiral threaded nails. You can remove them by getting a sharp instrument under the head of the nail and pry it up just a little bit (32nd of an inch) then grab the head of the nail with a good needle nose with serrations inside the tip and "unscrew" the fastener. The spiral threads are long helix. That means the threads only make about 1 revolution for each 1/2" of shank length. On re-assembly all you have to do is press the fastener back into the hole that it came out of.
__________________
Vacuum tubes are used in Wisconsin to help heat your house.

New Web Site under developement
ME http://AntiqueTvGuy.com
Reply With Quote
  #3  
Old 09-12-2020, 03:48 PM
dtvmcdonald's Avatar
dtvmcdonald dtvmcdonald is offline
VideoKarma Member
 
Join Date: Nov 2012
Posts: 1,268
Quote:
Originally Posted by ohohyodafarted View Post
I my memory serves me those are not rivets. They are actually long helix spiral threaded nails. f.
That's what I think. So far I've been unable to get them pried out far enough to
start unscrewing. I'll keep trying.
Reply With Quote
  #4  
Old 09-12-2020, 06:09 PM
ohohyodafarted's Avatar
ohohyodafarted ohohyodafarted is offline
Bob Galanter
 
Join Date: Sep 2005
Location: Whitefish Bay, Wi (Milwaukee)
Posts: 1,080
Try using a nice sharp 1/4" wide wood chisel. You should be able to force the sharp edge under the head and use the beveled side of the chisel as a fulcrum to pry upward. Place the beveled side of the chisel against the bakelite and the flat side of the chisel against the underside of the fasteners' head. You only need to pry the fastener up enough to get a grip on the head with your needle nose. From there, use your needle nose to pull up with a twisting motion in a (IIRC) counter clockwise direction.
__________________
Vacuum tubes are used in Wisconsin to help heat your house.

New Web Site under developement
ME http://AntiqueTvGuy.com
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:54 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.