Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > The Amateur Radio Spot

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 07-22-2020, 10:02 PM
Jeffhs's Avatar
Jeffhs Jeffhs is offline
<----Zenith C845
 
Join Date: Feb 2003
Location: Fairport Harbor, Ohio (near Lake Erie)
Posts: 4,035
Quote:
Originally Posted by jr_tech View Post
You might have better luck using these re-written instructions:

https://www.miklor.com/COM/UV_ProgMem.php

73, jr

Thanks much for that info. I'm sure it will help me quite a bit with setting the transmit offset for local repeaters (where I live, about 30 miles from Cleveland, there is only one local machine, about two miles or so from me, which I can use with a handheld--especially a 1.5-watt rig like my Baofeng UV5R+). As I said in my first post, I could not set the repeater offset on my Baofeng HT because the original instructions are about as clear as muddy water (!), but the rewritten Miklor instructions make a lot more sense; hopefully, I can go ahead, set up the radio for the local machine and be done with it. After 48 years in ham radio (got my first license at the age of 16 in 1972), this Baofeng HT is a real challenge for me (I never had a Chinese HT before this one; my other two HTs were made in Japan and have very understandable instruction manuals, although I cannot use one of the HTs [the Yaesu FT-207R] because the local repeater has 110.9Hz tone access, which that handheld does not support), but I'm sure with these revised programming instructions I can get this Baofeng rig working as intended.

Thanks again and 73,
__________________
Jeff, WB8NHV

Collecting, restoring and enjoying vintage Zenith radios since 2002

Zenith. Gone, but not forgotten.
Reply With Quote
  #2  
Old 08-08-2020, 09:31 PM
Jeffhs's Avatar
Jeffhs Jeffhs is offline
<----Zenith C845
 
Join Date: Feb 2003
Location: Fairport Harbor, Ohio (near Lake Erie)
Posts: 4,035
Quote:
Originally Posted by Jeffhs View Post
Thanks much for that info. I'm sure it will help me quite a bit with setting the transmit offset for local repeaters (where I live, about 30 miles from Cleveland, there is only one local machine, about two miles or so from me, which I can use with a handheld--especially a 1.5-watt rig like my Baofeng UV5R+). As I said in my first post, I could not set the repeater offset on my Baofeng HT because the original instructions are about as clear as muddy water (!), but the rewritten Miklor instructions make a lot more sense; hopefully, I can go ahead, set up the radio for the local machine and be done with it. After 48 years in ham radio (got my first license at the age of 16 in 1972), this Baofeng HT is a real challenge for me (I never had a Chinese HT before this one; my other two HTs were made in Japan and have very understandable instruction manuals, although I cannot use one of the HTs [the Yaesu FT-207R] because the local repeater has 110.9Hz tone access, which that handheld does not support), but I'm sure with these revised programming instructions I can get this Baofeng rig working as intended.

Thanks again and 73,
Update: I finally managed to set the repeater offset to +600kHz on my Baofeng UV-5R+ HT. It works--almost, as I can access the local repeater, but not very well. That is, I can access the machine from my home (about two miles away), but the two hams to whom I spoke last night have told me, while I am getting into the machine OK, my signal into the repeater is very noisy and scratchy, using the Baofeng UV-5R+; however, my Icom IC-T22A hits the machine just fine and the signal is 100 percent readable, so that will be the rig I will use from now on. There must be something about those Baofeng rigs the local repeater doesn't like, or perhaps the rig just doesn't have enough TX signal output to reach the machine solidly; I'm thinking the latter may well be the problem. However, I was informed by the amateur I spoke with last night that I might have better luck reaching the LCARA repeater if I would use the club's 440-MHz machine; I haven't tried that yet, but it's worth a shot. Perhaps that repeater is located geographically closer to me, or it may have a better antenna system (higher, more elements, etc.) than the 2m machine. I will just have to try it one of these days.

Oh well. I'm not licked yet. I have successfully checked into my club's 2m net via Echolink, so that will be the method I use to check into the net from now on. I can do so online with my computer (if I can ever find the correct password for the Qtel software), with my Icom HT, my Amazon Fire tablet, or my smartphone. I realize full well this will not be "real" ham radio, but from what I have read in this thread, I guess that is where the hobby is headed in the Internet age. I have tried several times tonight to find someone to talk with on the local repeater using my Icom HT, but received no replies, just a short "beep" followed by the squelch tail, which lets the operator know he or she is at least hitting the machine; this reinforces what I just said after having read the thread I just mentioned.

73,
__________________
Jeff, WB8NHV

Collecting, restoring and enjoying vintage Zenith radios since 2002

Zenith. Gone, but not forgotten.

Last edited by Jeffhs; 08-08-2020 at 09:57 PM.
Reply With Quote
  #3  
Old 08-08-2020, 10:55 PM
jr_tech's Avatar
jr_tech jr_tech is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 4,573
Make sure that you are in high power mode....briefly press the # button to toggle between high and low power. An indicator will be seen on the screen top left corner, indicating “L” if you are in low power mode.

jr
Reply With Quote
  #4  
Old 08-09-2020, 12:30 AM
Jeffhs's Avatar
Jeffhs Jeffhs is offline
<----Zenith C845
 
Join Date: Feb 2003
Location: Fairport Harbor, Ohio (near Lake Erie)
Posts: 4,035
Thank you for the info. I won't make the same mistake again. I do wish, however, that the Baofeng HTs would have been designed with an industry-standard antenna connector, rather than the non-standard one they do have. Unless one uses an after-market adapter, any other antenna than the stock one will not fit the antenna connector. The only exception to this is the Nagoya NA-771 VHF/UHF portable antenna, which has likely been designed for use with the Baofeng HTs (UV-5R, UV-5R+, et al).
__________________
Jeff, WB8NHV

Collecting, restoring and enjoying vintage Zenith radios since 2002

Zenith. Gone, but not forgotten.

Last edited by Jeffhs; 08-09-2020 at 12:37 AM.
Reply With Quote
  #5  
Old 08-09-2020, 10:06 PM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
Quote:
Originally Posted by Jeffhs View Post
Thank you for the info. I won't make the same mistake again. I do wish, however, that the Baofeng HTs would have been designed with an industry-standard antenna connector, rather than the non-standard one they do have. Unless one uses an after-market adapter, any other antenna than the stock one will not fit the antenna connector. The only exception to this is the Nagoya NA-771 VHF/UHF portable antenna, which has likely been designed for use with the Baofeng HTs (UV-5R, UV-5R+, et al).
That IIRC SMA type connector is industry standard. It's used in MRI systems and probably other brands of portable ham radio. You can get an SMA to PL-259 or SMA to BNC adapter if you want to use an older style antenna....When I bought my UV-5R on Amazon I also bought a SMA to PL-258 adapter for $7.
https://www.amazon.com/DHT-Electroni...028523&sr=8-11

Just because you haven't seen a connector before don't mean it's not a standard... New standards arise as technology advances, and some applications have standards that aren't common in other areas.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
Audiokarma
  #6  
Old 08-09-2020, 10:39 PM
mr_rye89's Avatar
mr_rye89 mr_rye89 is offline
VideoKarma Member
 
Join Date: Jul 2015
Location: The Luna's
Posts: 438
I use one of those Nagoya whips with my UV-5R (8 watt version), it works great for UHF, less good but still good for VHF. I can hear all 2M/70CM repeaters that are within 30 miles. I also have the USB adapter for mine and programmed all the FRS/GMRS/MURS frequencies in with CHIRP. I also added the local repeaters as channels because messing with the offset/sub audible tone every time you switch repeaters is a pain. I also fixed the squelch values on it too.

I also have an old Realistic HTX-202 VHF walkie, but the battery pack on it is hosed.
Reply With Quote
  #7  
Old 01-03-2021, 12:42 AM
Jeffhs's Avatar
Jeffhs Jeffhs is offline
<----Zenith C845
 
Join Date: Feb 2003
Location: Fairport Harbor, Ohio (near Lake Erie)
Posts: 4,035
Quote:
Originally Posted by mr_rye89 View Post
I use one of those Nagoya whips with my UV-5R (8 watt version), it works great for UHF, less good but still good for VHF. I can hear all 2M/70CM repeaters that are within 30 miles. I also have the USB adapter for mine and programmed all the FRS/GMRS/MURS frequencies in with CHIRP. I also added the local repeaters as channels because messing with the offset/sub audible tone every time you switch repeaters is a pain. I also fixed the squelch values on it too.

I also have an old Realistic HTX-202 VHF walkie, but the battery pack on it is hosed.
I have a Yaesu FT-207R HT which still works, last time I used it, some years ago. The battery pack went West several years ago, so I discarded the pack and put the HT itself in storage; it is still in storage to this day. I can't use the Yaesu HT anymore anyway, since the local 2m repeater now requires a 110.9 Hz PL tone (the Yaesu HT does not have a PL tone generator; I don't know if I could get one for an HT that old anymore). I bought a used Icom IC-T22A HT some time in the 1980s, when AES was still around; this little radio does have a PL tone board, so I can now get into the local 81/21 repeater just fine (I live only about a mile or so from the repeater).

As for the UV-5R VHF-UHF handheld, I have one but it doesn't work well enough to access the above- mentioned 81/21 repeater. That is, I can hit the repeater OK from my location, but not solidly; the last time I tried, I received a report to the effect that my signal was extremely scratchy and, of course, all but unreadable. When I switched to my Icom HT, the problem was solved. The only things I can think of are the battery pack in my UV-5R must have been too weak, or perhaps I wasn't using the proper antenna (I was using a very short rubber-duckie antenna on the radio at the time).
__________________
Jeff, WB8NHV

Collecting, restoring and enjoying vintage Zenith radios since 2002

Zenith. Gone, but not forgotten.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:55 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.