Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Rectangular Screen Tube Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 07-18-2020, 01:17 PM
BandDirector
Guest
 
Posts: n/a
The bell reads around 450 ohms, the wire about half.

The lugs are below in a pic, I think they are verticals.

Discovery: Top (left) is height, bottom (right) is vertical linerity. I couldn't read the words until now.

Height will backtrack as I turn towards the extreme end, instead of continuing to the bottom or past bottom of screen.
Attached Images
File Type: jpg 20200718_131039.jpg (58.0 KB, 9 views)

Last edited by BandDirector; 07-18-2020 at 01:30 PM.
Reply With Quote
  #2  
Old 07-18-2020, 01:54 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by BandDirector View Post
The bell reads around 450 ohms, the wire about half.
By half do you mean a 1/2 ohm, or 225 ohms? If 1/2 ohm you have a reasonable connection going to ground and you can cross that off as a problem.

Quote:
Originally Posted by BandDirector View Post
The lugs are below in a pic, I think they are verticals.
OK those controls are potentiometers generally refereed to as pots.

Quote:
Originally Posted by BandDirector View Post
Discovery: Top (left) is height, bottom (right) is vertical linerity. I couldn't read the words until now.

Height will backtrack as I turn towards the extreme end, instead of continuing to the bottom or past bottom of screen.
So how close are you to a full vertical picture now?
Reply With Quote
  #3  
Old 07-18-2020, 01:59 PM
BandDirector
Guest
 
Posts: n/a
Quote:
Originally Posted by Kevin Kuehn View Post
By half do you mean a 1/2 ohm, or 225 ohms? If 1/2 ohm you have a reasonable connection going to ground and you can cross that off as a problem.
Nope, around 225 ohms. So I guess a bad connection to the bell, and bad connection to the chassis/ground?

The image will not fill the screen, but it will get close, leaves about an inch gap at the bottom.

Last edited by BandDirector; 07-18-2020 at 02:14 PM.
Reply With Quote
  #4  
Old 07-18-2020, 08:06 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by BandDirector View Post
Nope, around 225 ohms. So I guess a bad connection to the bell, and bad connection to the chassis/ground?
The Dag coating itself will have resistance across itself, but from the chassis to the wire that contacts the Dag should be very low resistance. There's got to be a wire or sometimes a length of foil that makes that connection between the CRT mounting hardware and the chassis. I would think when you swapped chassis' that you may have run across it.

Quote:
Originally Posted by BandDirector View Post
The image will not fill the screen, but it will get close, leaves about an inch gap at the bottom.
And you still have the constant flicker?
Reply With Quote
  #5  
Old 07-18-2020, 08:13 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
If you have a clip lead(length of wire with alligator clips at each end), you could clip one end to the wire that contacts the Dag and the other to the chassis. If that makes no difference to the flicker then you can rule that connection out as a concern.
Reply With Quote
Audiokarma
  #6  
Old 07-18-2020, 09:55 PM
BandDirector
Guest
 
Posts: n/a
Quote:
Originally Posted by Kevin Kuehn View Post
If you have a clip lead(length of wire with alligator clips at each end), you could clip one end to the wire that contacts the Dag and the other to the chassis. If that makes no difference to the flicker then you can rule that connection out as a concern.
Did that a few steps back, didn't stop the flicker.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:21 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.