Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Antique Radio

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 06-27-2020, 11:25 AM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
OK well I think it was a little too early to celebrate, because the volume control started acting up again all the sudden, it was working perfectly but then all the sudden the volume got loud and the tone controls quit working again and the volume control is acting like a tone control again, so something must of happened to the capacitor I just stuck in there, which is weird because it was a brand new polypropolene capacitor that was never used so I wouldn't of thought that it would of shorted out or failed open suddenly...

I'm kind of getting tired of having to take this radio apart over and over again just to keep chasing down problems that keep cropping up one after another like this, they really didn't make this radio servicer friendly seeing as you have to go through the front and the back to remove the chassis screws and the knobs on the front are a pain in the butt to remove as well and the preset panel is also a pain to remove.

I can see why they didn't make this particular model of radio for very long.

Last edited by vortalexfan; 06-27-2020 at 11:44 AM.
Reply With Quote
  #2  
Old 06-27-2020, 12:12 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
Quote:
Originally Posted by vortalexfan View Post
...all the sudden the volume got loud and the tone controls quit working again and the volume control is acting like a tone control again...
By "got loud", you mean it went to full volume and you can't turn it down? If so, that suggests the bottom lug of the control has lost its ground connection (or rather its connection to R22).
Reply With Quote
  #3  
Old 06-27-2020, 12:36 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by old_coot88 View Post
By "got loud", you mean it went to full volume and you can't turn it down? If so, that suggests the bottom lug of the control has lost its ground connection (or rather its connection to R22).
No, more like it went to quarter volume and I can't turn the volume down or up anymore because the volume control just acts like a tone control again like it did before when that detector coupling cap was out of the circuit and the tone control pushbuttons aren't functioning anymore excecpt the one marked "normal" (which I'm assuming the "normal" button bypasses the tone control circuit all together).

And like I said it was working fine for about 15 minutes then it suddently quit working again.

I don't know if this is a clue or not as to what may have happened but when I first turned on the radio (after I installed the .01 MFD cap into that spot that was missing the cap for the volume control) there was a smell of melting solder like maybe something might of gotten hot enough to melt some solder, but I'm wondering if something in that detector to volume control coupling circtui got hot enough to melt the solder on that coupling cap I installed and made that capacitor come loose?
If so what would of gotten that hot in that circuit to melt the solder on that capacitor and cause it to come loose?

Last edited by vortalexfan; 06-27-2020 at 12:44 PM.
Reply With Quote
  #4  
Old 06-27-2020, 01:12 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
There's nothing associated with that circuit that should draw any current to speak of, let alone enough to melt solder. Anyhow, check for solid continuity (zero ohms) from C11 to where it connects to the IF can, and to the 1 meg resistor (R11).

From the other side of C11, check for continuity to the top lug of the vol control.

There's gotta be an open on one side or the other of C11.

Doubtful, but maybe the cap itself has gone open(?)
Reply With Quote
  #5  
Old 06-27-2020, 01:25 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by old_coot88 View Post
There's nothing associated with that circuit that should draw any current to speak of, let alone enough to melt solder. Anyhow, check for solid continuity (zero ohms) from C11 to where it connects to the IF can, and to the 1 meg resistor (R11).

From the other side of C11, check for continuity to the top lug of the vol control.

There's gotta be an open on one side or the other of C11.

Doubtful, but maybe the cap itself has gone open(?)
Well I kind of lied about that capacitor being unused, (actually it was more like I forgot) it was used as a DC Blocking cap for my Signal Generator, but I wouldn't think that that would cause the capacitor to fail prematurely, if that's actually what happened here...

Last edited by vortalexfan; 06-27-2020 at 01:31 PM.
Reply With Quote
Audiokarma
  #6  
Old 06-27-2020, 01:33 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
I have a .047 MFD capacitor, would that be ok in that spot if it turns out that the .01 capacitor did end up going bad?
Reply With Quote
  #7  
Old 06-27-2020, 02:18 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
It'd work, but with excessive bass.

But by all means, first check continuity as suggested, from C11 to where it enters the IF can, and to resistor R22. And from the other end of C11 to the top of the vol control.

Measure from right where the leads exit the capacitor body
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:51 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.