Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Diagnostic & Test Equipment

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 04-17-2020, 02:13 PM
jr_tech's Avatar
jr_tech jr_tech is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 4,573
Fort Wayne?

http://fortwaynehamfest.com

jr
Reply With Quote
  #2  
Old 04-17-2020, 04:44 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by jr_tech View Post
That's another city I'd rather not drive around in because traffic is terrible there and my mom doesn't want me to drive around there unless someone is with me for the reasons I mentioned.

Plus activities like that are canceled until further notice because of the corona virus.
Reply With Quote
  #3  
Old 04-17-2020, 11:24 PM
Notimetolooz's Avatar
Notimetolooz Notimetolooz is offline
VideoKarma Member
 
Join Date: Mar 2014
Location: Dallas, TX
Posts: 548
It is great that HP equipment is more affordable now. I have some myself and I don't usually spend a whole lot on things. That being said, you have to keep in mind that a piece of HP test equipment built in the 1950's will require re-capping just as a radio or TV from that era. HP used very high quality parts so they hold up better than others, but there are limits on how well anything lasts. Solid state test equipment made more recently are less likely to need restoration before they can be used. Repair shops in the 40's through the 70's seldom had HP equipment.
There are brands that fall between HP and say Heathkit in precision. Heathkit items are very easy to work on since they were intended for assembly from scratch. There are service grade brands with better performance that are factory built but are simpler than HP. B&K, RCA, EICO, Sencor, Leader and Tektronix, etc.
Here is my modified SG-8. My B&K 2005A RF generator and HP 5382A frequency counter. Also my Leader LAG-27 audio generator, a home-built 455KHz generator and my RF coupling loop. I think I found the SG-8 locally on Craig's list. The others were very carefully selected form ebay. The B&K RF generator had some broken front panel pieces (poor packing) that I was able to glue back together. Except for the SG-8 the equipment shown is solid state, but I think I replaced the electrolytics in all of them.
Attached Images
File Type: jpg EquipmentE3.jpg (82.4 KB, 20 views)
File Type: jpg EquipmentE1.jpg (93.2 KB, 24 views)
File Type: jpg EquipmentE2.jpg (70.8 KB, 19 views)

Last edited by Notimetolooz; 04-17-2020 at 11:30 PM. Reason: Additions
Reply With Quote
  #4  
Old 04-18-2020, 12:11 AM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by Notimetolooz View Post
It is great that HP equipment is more affordable now. I have some myself and I don't usually spend a whole lot on things. That being said, you have to keep in mind that a piece of HP test equipment built in the 1950's will require re-capping just as a radio or TV from that era. HP used very high quality parts so they hold up better than others, but there are limits on how well anything lasts. Solid state test equipment made more recently are less likely to need restoration before they can be used. Repair shops in the 40's through the 70's seldom had HP equipment.
There are brands that fall between HP and say Heathkit in precision. Heathkit items are very easy to work on since they were intended for assembly from scratch. There are service grade brands with better performance that are factory built but are simpler than HP. B&K, RCA, EICO, Sencor, Leader and Tektronix, etc.
Here is my modified SG-8. My B&K 2005A RF generator and HP 5382A frequency counter. Also my Leader LAG-27 audio generator, a home-built 455KHz generator and my RF coupling loop. I think I found the SG-8 locally on Craig's list. The others were very carefully selected form ebay. The B&K RF generator had some broken front panel pieces (poor packing) that I was able to glue back together. Except for the SG-8 the equipment shown is solid state, but I think I replaced the electrolytics in all of them.
OK, thanks for the info.
I'm just curious, how do you hook up a frequency counter to a signal generator if I got one?
Reply With Quote
  #5  
Old 04-18-2020, 12:59 PM
Notimetolooz's Avatar
Notimetolooz Notimetolooz is offline
VideoKarma Member
 
Join Date: Mar 2014
Location: Dallas, TX
Posts: 548
Good question. That points out a bit of a problem normally. The output of a typical RF generator is very small. It only takes something like 10 uV ( 10 one millionth of a volt) of signal at the radio antenna for the radio to receive it. The problem is many frequency counters need something like at least 100 mV for them to work. One thing to do is turn the generator output up to max to read the frequency and then turn the output down before connecting to the radio. Another thing that sometimes works is to modify the generator and bring out the signal before it goes into the output attenuator to a separate connector. The B&K 2005A has this already done. It has the normal output connector that the amplitude can be varied and a frequency monitoring output connector. Some people have bought small frequency counter modules and install them in the generator if there is room. I don't think the modules have a very precise timebase oscillator in them however.
Reply With Quote
Audiokarma
  #6  
Old 04-18-2020, 01:26 PM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
Quote:
Originally Posted by Notimetolooz View Post
Good question. That points out a bit of a problem normally. The output of a typical RF generator is very small. It only takes something like 10 uV ( 10 one millionth of a volt) of signal at the radio antenna for the radio to receive it. The problem is many frequency counters need something like at least 100 mV for them to work. One thing to do is turn the generator output up to max to read the frequency and then turn the output down before connecting to the radio. Another thing that sometimes works is to modify the generator and bring out the signal before it goes into the output attenuator to a separate connector. The B&K 2005A has this already done. It has the normal output connector that the amplitude can be varied and a frequency monitoring output connector. Some people have bought small frequency counter modules and install them in the generator if there is room. I don't think the modules have a very precise timebase oscillator in them however.
It the counter is microcontroller based and has a crystal osc it can be very precise.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
  #7  
Old 04-18-2020, 06:51 PM
Notimetolooz's Avatar
Notimetolooz Notimetolooz is offline
VideoKarma Member
 
Join Date: Mar 2014
Location: Dallas, TX
Posts: 548
Depends on how good the crystal oscillator is more than anything. You get what you pay for.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:32 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.