Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 04-03-2020, 09:52 PM
maxhifi's Avatar
maxhifi maxhifi is offline
VideoKarma Member
 
Join Date: Dec 2010
Posts: 1,871
Try watching something more recent, which was filmed at night. Old TV shows were made for old low contrast TV sets, so they probably will show the least benefit.
Reply With Quote
  #2  
Old 04-03-2020, 11:15 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by maxhifi View Post
Try watching something more recent, which was filmed at night. Old TV shows were made for old low contrast TV sets, so they probably will show the least benefit.
Good idea. For now I came up with an alternative that I think is valid. I figured my B&K 1077 would produce a representative light and dark raster that should allow me to take steady DC voltage measurements at the brightness pot wiper. B&K rf output connected through the tuner of the TV. The DC V measurements were taken at the brightness pot wiper which is also the cathode of the diode and top of the .1uf filter cap going to ground.

1. The B&K target measured about 90V DC.

2. Bright raster with no slide measured about 100V DC.

3. Black plastic in place of the slide produced 82V DC.

So a total DC swing of 18V at the wiper.

It clearly shows the diode is in fact rectifying the sync tips. How useful that amount of restoration is I have no idea. To me, visually it's a subtle effect, but like Max mentions I need to find some much better night video to put this to the test watching program material.

Disclaimer:

It's about impossible to take a picture of a dark raster, so the last image is fudged a little. But there were no controls adjusted on the TV while measuring the 3 DC voltages.






Last edited by Kevin Kuehn; 04-03-2020 at 11:21 PM.
Reply With Quote
  #3  
Old 04-03-2020, 11:41 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
This is how my TV was modified for the above measurements. And I just realized I didn't have the bleeder resistor across the diode when I did this. Not sure what if any effect that will have on the measurements. I had one in there early and didn't see much difference and then forgot to put it back.

Reply With Quote
  #4  
Old 04-04-2020, 12:07 AM
old_tv_nut's Avatar
old_tv_nut old_tv_nut is offline
See yourself on Color TV!
 
Join Date: Jul 2004
Location: Rancho Sahuarita
Posts: 7,815
Quote:
Originally Posted by Kevin Kuehn View Post
Good idea. For now I came up with an alternative that I think is valid. I figured my B&K 1077 would produce a representative light and dark raster that should allow me to take steady DC voltage measurements at the brightness pot wiper. B&K rf output connected through the tuner of the TV. The DC V measurements were taken at the brightness pot wiper which is also the cathode of the diode and top of the .1uf filter cap going to ground.

1. The B&K target measured about 90V DC.

2. Bright raster with no slide measured about 100V DC.

3. Black plastic in place of the slide produced 82V DC.

So a total DC swing of 18V at the wiper.

It clearly shows the diode is in fact rectifying the sync tips. How useful that amount of restoration is I have no idea. To me, visually it's a subtle effect, but like Max mentions I need to find some much better night video to put this to the test watching program material.
I think you misunderstood. In an ideal case, the brightness voltage and voltage on the 0.1 uf cap would be completely steady, so the sync tips would be clamped to a constant voltage no matter what the video content is.

The indication of the effectiveness of the DC restoration is the DC voltage measurement at the cathode. With no DC restoration, the change from bright scene to black scene will be minimal - it will just be set by the brightness pot. But with the DC restorer, the DC voltage will be high on the black scene and lower on the bright scene. Looking with the scope, set to DC coupling, the dark parts of a bright picture will be the same voltage as the black of a black screen (or almost the same, depending on how complete the DC restoration is).

Looking at your screen pics, you can see plainly that with the test pattern, the blacks are properly black, and with the black image they are still properly black, not gray, so the DC restoration is doing its thing. If you get an old movie that has spooky night scenes where nearly everything is dark, the picture will actually be dark like it should be, instead of foggy medium gray. This will not be visually subtle!

Your measurements at the wiper would indicate that the black level probably shifts about 8 volts when going from bright test pattern to full black. This is small compared to the full 50 v p-p video signal, so is much better than the non-DC- restored original.

If you look with a DC-coupled scope at the cathode, you will be able to see how little the black level shifts compared to the huge changes without DC restoration.
__________________
www.bretl.com
Old TV literature, New York World's Fair, and other miscellany

Last edited by old_tv_nut; 04-04-2020 at 12:10 AM.
Reply With Quote
  #5  
Old 04-04-2020, 12:47 AM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by old_tv_nut View Post
I think you misunderstood. In an ideal case, the brightness voltage and voltage on the 0.1 uf cap would be completely steady, so the sync tips would be clamped to a constant voltage no matter what the video content is.

The indication of the effectiveness of the DC restoration is the DC voltage measurement at the cathode. With no DC restoration, the change from bright scene to black scene will be minimal - it will just be set by the brightness pot. But with the DC restorer, the DC voltage will be high on the black scene and lower on the bright scene. Looking with the scope, set to DC coupling, the dark parts of a bright picture will be the same voltage as the black of a black screen (or almost the same, depending on how complete the DC restoration is).

Looking at your screen pics, you can see plainly that with the test pattern, the blacks are properly black, and with the black image they are still properly black, not gray, so the DC restoration is doing its thing. If you get an old movie that has spooky night scenes where nearly everything is dark, the picture will actually be dark like it should be, instead of foggy medium gray. This will not be visually subtle!

Your measurements at the wiper would indicate that the black level probably shifts about 8 volts when going from bright test pattern to full black. This is small compared to the full 50 v p-p video signal, so is much better than the non-DC- restored original.

If you look with a DC-coupled scope at the cathode, you will be able to see how little the black level shifts compared to the huge changes without DC restoration.
Thanks for explaining in greater detail. I installed a 1 meg bleeder across the diode which resulted in less change at the brightness wiper, and the voltage change at the cathode being greater. Seems like what was lost at the brightness wiper was added to the cathode. I find it very difficult to monitor the black level of a playing video on the scope. Using the B&K test pattern was the only way I could see it change, or not.

Last edited by Kevin Kuehn; 04-04-2020 at 12:53 AM.
Reply With Quote
Audiokarma
  #6  
Old 04-04-2020, 08:23 AM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
I believe a portion of this lack of black level comes from some sets having lower B+ headroom. The B+ on this TV I'm experimenting with has close to 250v vs Max's set at 150v. My contrast control has a range that allows high black level's even without the dc restoration circuit present. I find that most video I watched growing up was fairly consistent within a given program. I suspect there was some type of video compression used during the production process back in the 60's though 70's. I can basically set it and forget it. I'm not sure if modern day video content would be worse in that respect. Honestly I don't have much desire to watch new programing on my vintage sets. I do find the audio processing on today's movies quite poor in comparison to older material. Or possibly there's a trend back towards less processing? With my ageing ears I struggle to hear the quieter passages, and soon after being blown away. IMO too much dynamics. Similarly I don't see the range of video dynamics in nature that we expect to see from from our television sets. When ambient lighting is low the human eye tends to see less contrast.

Last edited by Kevin Kuehn; 04-04-2020 at 08:26 AM.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:33 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.