Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Rectangular Screen Tube Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 03-15-2020, 08:43 AM
JohnCT's Avatar
JohnCT JohnCT is offline
VideoKarma Member
 
Join Date: Jan 2020
Posts: 749
You should be able to find a transformer for that unit. Make sure you don't run a new one until you monitor the current from the 5U4 output.

Most TVs of that era used very similar transformers. If you can't find one, one from a junk chassis can be made to work without too much effort. Make sure the one you're subbing has sufficient filament current capability, or you can add a filament transformer in place of the original filament winding. You may have to add a dropping resistor if a replacement transformer has too much B+.

In any case, that's a very unique and handsome console in an era where they often weren't.

Oh, and welcome to Videokarma.

John
Reply With Quote
  #2  
Old 03-15-2020, 10:02 AM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
Others' opinions may vary, but here's my $.02 worth..

1. Service-wise, those early printed circuit layouts were the worst ever conceived, with the foil side of the boards made inaccessable (what were they smokin' to come up with that idea? Musta thought the design was bulletproof and would never need troubleshooting.

2. The newly-introduced small neck CRTs usually died an early death. Before proceeding any further, find someone with a CRT tester to verify that (if by some miracle) the CRT is good.

Last edited by old_coot88; 03-15-2020 at 10:08 AM.
Reply With Quote
  #3  
Old 03-15-2020, 01:09 PM
JohnCT's Avatar
JohnCT JohnCT is offline
VideoKarma Member
 
Join Date: Jan 2020
Posts: 749
Quote:
Originally Posted by old_coot88 View Post
Others' opinions may vary, but here's my $.02 worth..

1. Service-wise, those early printed circuit layouts were the worst ever conceived, with the foil side of the boards made inaccessable (what were they smokin' to come up with that idea? Musta thought the design was bulletproof and would never need troubleshooting.
True. Don't have a clue what they were thinking other than having exceptional built-in shielding. I worked on a few when I was a young shaver, and my dad had me tack in the defective part on top of the board. Once the TV was running, he had me remove the circuit board and place the components as the factory did.

One good thing about it was that you had to use more technique than just shotgunning if you wanted a nice neat job. Later on, when RCA went to their "unitized" chassis (no more modules), the technique as described in the service manuals was to cut the defective part off the top of the board and solder a new one in place using the old leads. The reason is that RCA used a conformal coating on the bottom they did not want to be disturbed. I used to install those parts through the board despite RCA's admonition not to.


Quote:
Originally Posted by old_coot88 View Post
2. The newly-introduced small neck CRTs usually died an early death. Before proceeding any further, find someone with a CRT tester to verify that (if by some miracle) the CRT is good.
Another good point that I totally missed.

John
Reply With Quote
  #4  
Old 03-15-2020, 11:13 PM
BandDirector
Guest
 
Posts: n/a
Quote:
Originally Posted by old_coot88 View Post
Others' opinions may vary, but here's my $.02 worth..

1. Service-wise, those early printed circuit layouts were the worst ever conceived, with the foil side of the boards made inaccessable (what were they smokin' to come up with that idea? Musta thought the design was bulletproof and would never need troubleshooting.

2. The newly-introduced small neck CRTs usually died an early death. Before proceeding any further, find someone with a CRT tester to verify that (if by some miracle) the CRT is good.
As to number 2: I purchased an old CRT tester for Color/B&W from eBay. When I run 6.3 volts to the tube heaters I see a near 80% for cathode grid and cathode; if I switch it from quality to leak I don't see the indicator glow for a leak for the cathode. I'm assuming 6.3 volts is the correct test voltage, and it seems that the transformer has a 6.3 volt lead.
Reply With Quote
  #5  
Old 03-15-2020, 11:14 PM
BandDirector
Guest
 
Posts: n/a
Quote:
Originally Posted by JohnCT View Post
You should be able to find a transformer for that unit. Make sure you don't run a new one until you monitor the current from the 5U4 output.

Most TVs of that era used very similar transformers. If you can't find one, one from a junk chassis can be made to work without too much effort. Make sure the one you're subbing has sufficient filament current capability, or you can add a filament transformer in place of the original filament winding. You may have to add a dropping resistor if a replacement transformer has too much B+.

In any case, that's a very unique and handsome console in an era where they often weren't.

Oh, and welcome to Videokarma.

John
Thanks for the welcome!

It is a very unique and handsome tv, I'm hellbent on restoring it so that I can use it the way it deserves.

What is B+, and, what do I need to worry about?
Reply With Quote
Audiokarma
  #6  
Old 03-16-2020, 06:47 AM
JohnCT's Avatar
JohnCT JohnCT is offline
VideoKarma Member
 
Join Date: Jan 2020
Posts: 749
Quote:
Originally Posted by BandDirector View Post

What is B+, and, what do I need to worry about?
In your schematic, you'll see the 5U4 rectifier tube.



That, along with the filtering capacitors, is what turns the AC voltage from the transformer secondary to the DC voltage that the TV circuits need. The 281V point on pin 2 of the 5U4 is called B+ voltage.

The term itself is a throwback to the very early radios which were powered by batteries. Radios had "A" batteries, "B" batteries, and "C" batteries.

Why it's important is that any excessive load or short on the secondary of the transformer can cause it to fail. Why your transformer failed is something we don't know right now - it could have been a bad 5U4 or a short or loading down of the 281V B+ line. It also could have just failed on it's own by developing a shorted turn or there could have been a prolonged load on it.

Monitoring the current in the B+ line and monitoring the current on the AC input side is important if we install a new transformer and want to be sure that there is no other problem in the TV chassis that would overheat or otherwise damage the new transformer.

John

Last edited by JohnCT; 03-16-2020 at 06:55 AM.
Reply With Quote
  #7  
Old 03-16-2020, 12:24 PM
BandDirector
Guest
 
Posts: n/a
Quote:
Originally Posted by JohnCT View Post
In your schematic, you'll see the 5U4 rectifier tube.



That, along with the filtering capacitors, is what turns the AC voltage from the transformer secondary to the DC voltage that the TV circuits need. The 281V point on pin 2 of the 5U4 is called B+ voltage.

The term itself is a throwback to the very early radios which were powered by batteries. Radios had "A" batteries, "B" batteries, and "C" batteries.

Why it's important is that any excessive load or short on the secondary of the transformer can cause it to fail. Why your transformer failed is something we don't know right now - it could have been a bad 5U4 or a short or loading down of the 281V B+ line. It also could have just failed on it's own by developing a shorted turn or there could have been a prolonged load on it.
I am having trouble with black and red/black lead, when I run ac to them they hum and cause smoke. If I run hot to the red only, I seem to get more accurate readings without hum. It seems there is a short between the primary winding? What else causes a hum with just black and and red/black to black and red on incoming a/c?
Reply With Quote
  #8  
Old 03-16-2020, 02:58 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
You shouldn't be running AC to anything but black & red/black, nowhere else. That's the primary of the xfmr. Do this -

Remove all the tubes except the high voltage rectifier (probably 1B3)*. This removes all loads from the secondaries of the power xfmr. Now run AC to the primary (black & red/black) again. If the xfmr still smokes, it's shot.

*The 1B3's filament runs off the flyback.
Reply With Quote
  #9  
Old 03-16-2020, 04:23 PM
BandDirector
Guest
 
Posts: n/a
Quote:
Originally Posted by old_coot88 View Post
You shouldn't be running AC to anything but black & red/black, nowhere else. That's the primary of the xfmr. Do this -

Remove all the tubes except the high voltage rectifier (probably 1B3)*. This removes all loads from the secondaries of the power xfmr. Now run AC to the primary (black & red/black) again. If the xfmr still smokes, it's shot.

*The 1B3's filament runs off the flyback.

It's shot. Smokeup and sizzle with no load and completely disconnected.
Reply With Quote
  #10  
Old 03-16-2020, 04:52 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
99.999% certain it's shot. But just to be 100.00% certain, do this:

On the off chance there's a hard short on the heater (filament) rail, disconnect the brown & brown/black wires so they 'float' free.

On the off chance there's a hard short in the 5U4 socket, disconnect the red & red/green wires* from the socket so they float free. (pins 4 and 6 respectively.)

Apply power to the primary as before. If the xfmr still smokes, 100.00% it's shot.

*Careful. There's normally around 800 - 900 VAC between these two.
Reply With Quote
Audiokarma
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:52 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.