Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 11-21-2019, 01:59 AM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by Eric H View Post
That looks like a Thermistor, I seem to recall replacing one in my set. If it is you could just jumper it and power it up with a variac or dim bulb tester.
You mean the mystery part?
If so what was the purpose of that thermistor in that spot, and how do I jump it?
Reply With Quote
  #2  
Old 11-21-2019, 10:22 AM
Dubis7's Avatar
Dubis7 Dubis7 is offline
Alchemizes cash to tubes
 
Join Date: Nov 2014
Location: Leesburg, VA.
Posts: 397
Quote:
Originally Posted by vortalexfan View Post
You mean the mystery part?
If so what was the purpose of that thermistor in that spot, and how do I jump it?
My understanding is that thermistors are a sort of heat-responsive resistor. It starts out with high resistance to prevent current inrush on power up, and quickly drops to basically 0 as the set warms up. It's a protection thing, but you should be safe to eliminate it for now.

You could literally use alligator clips on either side or solder a wire to bypass it for the time being. I'd recommend replacing it if it's bad, though.

Feel free to correct me if I'm wrong. I'm not nearly as experienced as some people here.
__________________
To keep your tubes running smoothly, make sure to dust underneath the glass as well.
Reply With Quote
  #3  
Old 11-21-2019, 11:09 AM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
Quote:
Originally Posted by Dubis7 View Post
My understanding is that thermistors are a sort of heat-responsive resistor. It starts out with high resistance to prevent current inrush on power up, and quickly drops to basically 0 as the set warms up. It's a protection thing, but you should be safe to eliminate it for now.

You could literally use alligator clips on either side or solder a wire to bypass it for the time being. I'd recommend replacing it if it's bad, though.

Feel free to correct me if I'm wrong. I'm not nearly as experienced as some people here.
A common repair mans trick was to just twist the leads together... replacement is better but not strictly necessary in most sets.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
  #4  
Old 11-22-2019, 12:23 AM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by Electronic M View Post
A common repair mans trick was to just twist the leads together... replacement is better but not strictly necessary in most sets.
ok, I'll give it a shot.
Reply With Quote
  #5  
Old 11-22-2019, 12:49 AM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Good News, it was just a failed Thermistor, as soon as I bypassed it using the method Electronic M suggested, the TV powered up and the TV was working perfectly, no distortions in the screen or anything, nice full screened raster with snow and white noise to go with it, all while working with its original RCA branded tubes.

See Picture Below.
Attached Images
File Type: jpg RCA TV.jpg (41.3 KB, 44 views)
Reply With Quote
Audiokarma
  #6  
Old 11-22-2019, 01:47 AM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Here's some even better news, I think this TV is a low hours set because after I left the tv sit powered on for 5 minutes the picture became nice and bright!

I have a feeling that what happened with this TV is that it got struck by lightning at some point in time and the lightning strike fried the thermistor which saved everything else in the TV thankfully and so the owners of the TV just put it away and bought a new TV to replace it because they thought the TV was toast and didn't want to pay to have a repairman out to look at the set.

unfortunately the brightness control don't work right and on the ride home the the vertical hold knob broke.
Reply With Quote
  #7  
Old 11-21-2019, 02:51 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by Dubis7 View Post
My understanding is that thermistors are a sort of heat-responsive resistor. It starts out with high resistance to prevent current inrush on power up, and quickly drops to basically 0 as the set warms up. It's a protection thing, but you should be safe to eliminate it for now.

You could literally use alligator clips on either side or solder a wire to bypass it for the time being. I'd recommend replacing it if it's bad, though.

Feel free to correct me if I'm wrong. I'm not nearly as experienced as some people here.
Ok, thanks, that might be why it's refusing to power up because that thermistor thingy is burned to a crisp and broken in half.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:30 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.