Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 11-06-2019, 11:51 AM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by vortalexfan View Post
OK So here's a YouTube Link to my Video showing what the TV is currently doing.

https://youtu.be/TfFZxX8DOQU

Hopefully this will work better, and won't require you to log into a Google Account.

P. S. You'll have to turn up the volume really loud to hear the audio.
I'm not sure what I'm suppose to be hearing in that video?

Say... what ever happened you measuring those voltages I asked about per Sams voltage chart on the pins of the 6V6 audio output tube? When I asked you a couple pages back, you said you hadn't yet, but were instead going to replace every resistor because they were all bad? Those voltage measurements in that stage could be crucial to figuring out why R62 is overheating and the cause of your excess current draw. That circuit derives it's supply directly from the focus control through R62 and the voltages developed are provided to the entire audio circuit. I'm getting the impression that you prefer avoiding any troubleshooting, but would rather replace every component in sight. Eventually you're going to run out of components to replace, and then what?

Last edited by Kevin Kuehn; 11-06-2019 at 11:58 AM.
Reply With Quote
  #2  
Old 11-06-2019, 11:57 AM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by Kevin Kuehn View Post
I'm not sure what I'm suppose to be hearing in that video?

Say... what ever happened you measuring those voltages I asked about per Sams voltage chart on the pins of the 6V6 audio output tube? When I asked you a couple pages back, you said you hadn't yet, but were instead going to replace every resistor because they were all bad? Those voltage measurements in that stage could be very crucial to figuring out why R62 is overheating and the cause of your excess current draw. That circuit derives it's supply directly from the focus control through R62 and the voltages are provided to the entire audio circuit. I'm getting the impression that you prefer troubleshooting, but would rather replace every component in sight.
Well I'm hearing what sounds like vertical or horizontal oscillation going on, but I'm not sure if that's what I'm hearing or not, it's a kind of medium pitched rapid snapping noise, very similar to a taser going off.
I need confirmation as to whether or not that's the vertical, horizontal or high voltage running.

As for the voltages on the 6V6, I got side tracked, I have ADHD, so I get side tracked easily.
I'll get right to measuring those voltages.

Last edited by vortalexfan; 11-06-2019 at 12:03 PM.
Reply With Quote
  #3  
Old 11-06-2019, 12:13 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
OK, I'll be looking forward to those voltage measurements. My next question is do you have a high voltage probe? If not a probe how about a compact florescent bulb? You need something to indicate the presence of high voltage. Once you know you have HV, my next concern would be adjusting the ion trap. The ion trap has to be set properly or you'll never see a raster.
Reply With Quote
  #4  
Old 11-06-2019, 12:27 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by Kevin Kuehn View Post
OK, I'll be looking forward to those voltage measurements. My next question is do you have a high voltage probe? If not a probe how about a compact florescent bulb? You need something to indicate the presence of high voltage. Once you know you have HV, my next concern would be adjusting the ion trap. The ion trap has to be set properly or you'll never see a raster.
Ok, so pin 3 of the 6V6 tube is giving a funky reading, it's giving a reading of -0.195vdc which doesn't seem right...
And that reading was taken in reference to pin 8 of the 6V6 tube just like the manual said.

And no, I don't have a high voltage probe.
I do have some CFLs but they're all burned out or broken unfortunately.
Reply With Quote
  #5  
Old 11-06-2019, 12:38 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
What did pin 4 measure? If you have dc voltage on pin 4(screen) and nothing on 3(plate)I'd suspect the primary of your output transformer could be shorting to ground. You could also try measuring those two pins in respect to chassis ground. Any voltage readings on those two pins will indicate if there's a short in that transformer primary.
Reply With Quote
Audiokarma
  #6  
Old 11-06-2019, 12:48 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by Kevin Kuehn View Post
What did pin 4 measure? If you have dc voltage on pin 4(screen) and nothing on 3(plate)I'd suspect the primary of your output transformer could be shorting to ground. You could also try measuring those two pins in respect to chassis ground. Any voltage readings on those two pins will indicate if there's a short in that transformer primary.
Actually the output tranny is attached to the speaker and the speaker unplugs from the chassis, and it's currently not connected to the TV, would not having the speaker in circuit mess things up?
Reply With Quote
  #7  
Old 11-06-2019, 12:54 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by vortalexfan View Post
Actually the output tranny is attached to the speaker and the speaker unplugs from the chassis, and it's currently not connected to the TV, would not having the speaker in circuit mess things up?
Well of course if the output transform is unplugged. You see on the schematic that the b+ goes from one side of the transformers primary to the other side connected to pin 3(plate) of the output tube. But still it does not explain why R62 would be over heating while that speaker is unplugged, if in fact that's what's going on.
Reply With Quote
  #8  
Old 11-06-2019, 01:57 PM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
Quote:
Originally Posted by vortalexfan View Post
Actually the output tranny is attached to the speaker and the speaker unplugs from the chassis, and it's currently not connected to the TV, would not having the speaker in circuit mess things up?
It will mess quite a lot up. This set uses a stacked B+ scheme. The audio output stage acts as a series dropping resistance. The video output, IF and possibly the tuner depend on the audio output to supply them with B+.

From here on out make sure the speaker transformer is connected on every power up of the chassis.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
  #9  
Old 11-06-2019, 12:51 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Another thought... pull the 6V6 and see if the voltage on pin 3 changes, either referenced from pin 8 or ground.
Reply With Quote
  #10  
Old 11-06-2019, 02:14 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by Kevin Kuehn View Post
Another thought... pull the 6V6 and see if the voltage on pin 3 changes, either referenced from pin 8 or ground.
6v6 tube pulled I get over 300 volts DC on pin 3 of the 6V6 tube socket, and it drops as the rest of the tubes warm up. Perhaps I have bad 6V6 tubes?!

Edit: I installed a known good (a brand new never used Sovtek 6V6 tube) into the TV and measured Pin 3 in reference to ground and got over 300 VDC on pin 3 and got some audio out of ther speaker as well, but when pin 3 is measured against pin 8 of the 6V6 tube as per the manual I only get 25-30 VDC on pin 3.

Last edited by vortalexfan; 11-06-2019 at 02:29 PM.
Reply With Quote
Audiokarma
  #11  
Old 11-06-2019, 02:09 PM
vortalexfan vortalexfan is offline
VideoKarma Member
 
Join Date: Sep 2018
Location: Northern Indiana
Posts: 1,992
Quote:
Originally Posted by Kevin Kuehn View Post
What did pin 4 measure? If you have dc voltage on pin 4(screen) and nothing on 3(plate)I'd suspect the primary of your output transformer could be shorting to ground. You could also try measuring those two pins in respect to chassis ground. Any voltage readings on those two pins will indicate if there's a short in that transformer primary.
Pin 4 is spot on voltage wise on the 6V6 tube, and pin 3 once I connected the speaker was giving me a +25 vdc and dropping. So not sure what's going on with that.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:18 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.