Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 10-02-2019, 06:32 PM
static1701's Avatar
static1701 static1701 is offline
VideoKarma Member
 
Join Date: Mar 2019
Posts: 89
Quote:
Originally Posted by Electronic M View Post
With all those tubular caps on the board in your last pic the vertical would not work right even with new integrators...I just did a couple of these sets that were producing raster but had terrible vertical non-linearly and the paper caps were causing it....one even split open and started smoking while I was diagnosing the issue.
I ordered all the replacement caps today. I had to get the Factory service manual because the numbers on the board did not match the numbers in the Sams parts list. I am debating removing the board from the chassis or just clip and solder. I don't really care about keeping it original... I just want it to work correctly.
Reply With Quote
  #2  
Old 10-02-2019, 06:57 PM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
Quote:
Originally Posted by static1701 View Post
I ordered all the replacement caps today. I had to get the Factory service manual because the numbers on the board did not match the numbers in the Sams parts list. I am debating removing the board from the chassis or just clip and solder. I don't really care about keeping it original... I just want it to work correctly.
If it is a 10L43 with holes under the PCB like mine you can split the difference... leave all the wires connected, remove all the hold down screws on the board, unscrew the vertical transformer, and lift the fingers that he the wires to the chassis...you can lift the board enough to get to all the pads underneath through the holes with a thin iron....you can leave all the wires connected this way.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
  #3  
Old 10-06-2019, 06:26 AM
decojoe67's Avatar
decojoe67 decojoe67 is offline
VideoKarma Member
 
Join Date: Apr 2011
Location: Long Island, NY
Posts: 1,322
Quote:
Originally Posted by static1701 View Post
I ordered all the replacement caps today. I had to get the Factory service manual because the numbers on the board did not match the numbers in the Sams parts list. I am debating removing the board from the chassis or just clip and solder. I don't really care about keeping it original... I just want it to work correctly.
A friend of mine has done vintage TV repairs since the '60's, and a countless number of Predicta's. He laughs at the hassle most people make out of repairing them. The as-found Debutante I have, he repaired while I waited without removing anything. The sets been working fine for me 10 years later. It's nice doing an intense restoration of any old chassis, but it isn't necessary - and sometimes will cause more problems.
Reply With Quote
  #4  
Old 10-06-2019, 06:43 PM
static1701's Avatar
static1701 static1701 is offline
VideoKarma Member
 
Join Date: Mar 2019
Posts: 89
Pulling the board

Quote:
Originally Posted by decojoe67 View Post
A friend of mine has done vintage TV repairs since the '60's, and a countless number of Predicta's. He laughs at the hassle most people make out of repairing them. The as-found Debutante I have, he repaired while I waited without removing anything. The sets been working fine for me 10 years later. It's nice doing an intense restoration of any old chassis, but it isn't necessary - and sometimes will cause more problems.
I am torn as far as how I want to do it, one day I feel like I should pull the board and replace everything and the next day I think I will just clip and solder just what needs replacement. I have been looking at connectors online and thinking about adding a connection to all the wires to make it easier for next time. I just don't know. The new networks arrived the other day and I am just waiting on the rest of the caps to arrive before I get started.
Reply With Quote
  #5  
Old 10-06-2019, 10:00 PM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
Quote:
Originally Posted by static1701 View Post
I ordered all the replacement caps today. I had to get the Factory service manual because the numbers on the board did not match the numbers in the Sams parts list. I am debating removing the board from the chassis or just clip and solder. I don't really care about keeping it original... I just want it to work correctly.
If it is a 10L43 (or similar) with holes under the PCB like mine you can split the difference... leave all the wires connected, remove all the hold-down screws on the board, unscrew the vertical transformer, and lift the fingers that hold down the wire harness to the chassis...Then you can lift the board enough to get to all the pads underneath through the holes with a thin iron (or at least not obtusely large Iron)....you can leave all the wires connected and change any/every part on the board this way, and it is a heck of a lot less invasive and less work than removing/unwiring the whole board from the set and reinstalling it wire by wire.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
Audiokarma
  #6  
Old 10-07-2019, 06:02 AM
static1701's Avatar
static1701 static1701 is offline
VideoKarma Member
 
Join Date: Mar 2019
Posts: 89
Quote:
Originally Posted by Electronic M View Post
If it is a 10L43 (or similar) with holes under the PCB like mine you can split the difference... leave all the wires connected, remove all the hold-down screws on the board, unscrew the vertical transformer, and lift the fingers that hold down the wire harness to the chassis...Then you can lift the board enough to get to all the pads underneath through the holes with a thin iron (or at least not obtusely large Iron)....you can leave all the wires connected and change any/every part on the board this way, and it is a heck of a lot less invasive and less work than removing/unwiring the whole board from the set and reinstalling it wire by wire.
It is a 10L43, I will give this a try first.

Thanks
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:42 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.