Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 03-30-2019, 07:27 PM
Hugo barbedo Hugo barbedo is offline
VideoKarma Member
 
Join Date: Jul 2018
Posts: 24
Hi
good news and not so good news

the first powerup was somewhat sucessfull
the crt looks very strong, i have the brightness in the middle and contrast at 3/4.
the IF section seems to be working fine, although its strange that i have my modulator on channel 3 and can only tune it in on channel 5 on the tv...
sound is good even when there is lots of white content
the horizontal locks very well with the welding machine double diode
the vertical is not so great
i am having this foldover problem where the bottom part of the picture is missing and its appearing on the top of the raster. the raster is not centered on the screen and its not a problem of messing with the centering rings. i can fill up the screen by turning up the height control but the scanlines become huge and i loose vertical lock. also if i dont have a picture tuned in the raster fills up the screen
the video amp/sync separator tube is new and with the old one its the same
voltage checks on the vertical output/oscillator dont reveal any problem. all the voltages are preety much spot on
WP_20190331_00_08_20_Pro.jpg
on the yoke there is a black wire going to a metal wire that touches the screen aquadag...that is broken and makes the picture completely jumpy like when we loose vertical lock...bridging it with the black jumper wire seems to cure the problem but if i try to ground it to chassis the left side of the image collapses making a triangular shaped raster, very cool...i wonder if i have other broken connection or wire on the yoke causing the foldover...would it be possible? if so it would prevent me from chasing ghosts around the sync and vertical sections
there is an adjustable magnet on the left side of the yoke that has signs of abuse and the tube socket of the 6aw8a is also very abused, so it appears to me that someone ditched the tv because they could not fix this very problem...looks like i have a tough dog here, with me ususally its never the capacitors
WP_20190331_00_08_32_Pro.jpg
any ideas will be greatly appreciated


edit:
this is my scope on the pin 6 of the 6dr7
that is the plate of the vert oscillator
by looking at this i see the patient is suffering from serious heart disease...the drive is not linear, a wide pulse then a short one, then a wide one and so on, looks like it skips a beat every 2 cycles
the amplitude of the pulses looks ok , i am on 10x probe with 5v per division and the scope is not well calibrated so it seems decent to me. (maybe 120v PP)
what the hell can cause this???
WP_20190331_19_09_29_Pro.jpg

Last edited by Hugo barbedo; 03-31-2019 at 01:26 PM. Reason: added information
Reply With Quote
  #2  
Old 03-31-2019, 02:26 PM
Hugo barbedo Hugo barbedo is offline
VideoKarma Member
 
Join Date: Jul 2018
Posts: 24
ok so i am getting there slowly i think


c15.jpg
my tv has an additional panel on the right of the chassis with 2 additional linearity pots for the vertical that are not present on the american sets and consequently not listed on the schematics that i have
capacitor c15 is absent on my tv and on its place there is a capacitor connecting to that said panel
removing that capacitor and putting a 4n7 capacitor on the position of c15 makes the foldover go away and the pulses for the vertical drive are looking very good now
now i just have a totally squished top on the picture

i am at the point where i am thinking of removing the two linearity pots and recreate the "american"style circuit, that has to work but i consider it cheating.
WP_20190331_20_05_30_Pro.jpg
here each cycle is completed in 20miliseconds and that is equal to 50hz so we are good. the sawtooth looks preety also with a very short fall time (perfectly vertical slope)
WP_20190331_20_05_51_Pro.jpg

Last edited by Hugo barbedo; 03-31-2019 at 03:54 PM.
Reply With Quote
  #3  
Old 03-31-2019, 03:49 PM
Hugo barbedo Hugo barbedo is offline
VideoKarma Member
 
Join Date: Jul 2018
Posts: 24
I am almost done
just need to find were i put my test pattern dvd and play a little with the value of r27...on 17 inch sets philco seems to use a 100k, on 23 inch sets (11n56) they use a 68k, i will put a 82k
i am taking notes of all the changes i made until i find the proper italian schematic, if i do find it one day i can reverse all the mods and be able to use the extra 2 linearity pots.
i dont think it was me recapping the set that created this problem because i took pictures before the work and i have been comparing them and i did everything as it was...this tv had lots of repairs done and non original components. i think i am being lucky so far.

WP_20190331_21_04_24_Pro.jpg
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:34 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.