Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Diagnostic & Test Equipment

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 06-05-2017, 12:18 AM
Jon A.'s Avatar
Jon A. Jon A. is offline
Don't mess with Esther.
 
Join Date: Jun 2013
Location: Canada
Posts: 4,267
Quote:
Originally Posted by Findm-Keepm View Post
Two additions:

VTVM - Only one way to go, the RCA/Viz Senior or Master VoltOhmist.

We also had a nice Zenith Ultrasonic and IR remote tester. It had added features for measuring drive on the System 3 sets, but 90% used for IR remote control testing. I know of only one other way to test ultrasonic remotes sans the TV...the Zenith tester paid for itself over and over. Hard to find, I still have ours. It just uses an ultrasonic mic, and overdrives an op amp to square up things before sending it to both an LED and a scope jack. The iR side sends the IR diode/receiver output along a similar path.

Overkill for a newbie, but it completes my lineup
I know my Zenith 852-240 ultrasonic remote tester can be modded to test IR remotes, but is there another model that's a factory job? Mine has an "output to frequency counter" jack; I'm guessing a scope can be used with mine as well. That would be good because I don't have a frequency counter.
Reply With Quote
  #2  
Old 06-05-2017, 04:09 AM
Findm-Keepm's Avatar
Findm-Keepm Findm-Keepm is offline
Followin' the Rules...
 
Join Date: Jun 2007
Posts: 2,857
Quote:
Originally Posted by Jon A. View Post
I know my Zenith 852-240 ultrasonic remote tester can be modded to test IR remotes, but is there another model that's a factory job? Mine has an "output to frequency counter" jack; I'm guessing a scope can be used with mine as well. That would be good because I don't have a frequency counter.
Yes, we modded ours - originally it was ultrasonic only, but a Zenith service seminar in 79 or 80 gave up the kit number for the IR mod, which also included the instructions to mod it to verify drive signals on the early System IIIs. They demo'ed it at the service seminar connected to an oscope, for purely visual means. We used it autonomously and rarely connected it to anything. Don't leave it on - the battery dies quickly.

The IR mod kit had the IR diode, wires, instructions and a template for the drilling of the metal case. We got our kit from Bluefield distributing, and they were surprised to see us order it, apparently unaware of it's purpose. They sure knew lots of other time-savers.
__________________
Brian
USN RET 22YRS (Avionics/Cal)
CET-Consumer Repair and Avionics ('88)
"Capacitor Cosmetologist since '79"

When fuses go to work, they quit!
Reply With Quote
  #3  
Old 06-05-2017, 04:42 PM
Jon A.'s Avatar
Jon A. Jon A. is offline
Don't mess with Esther.
 
Join Date: Jun 2013
Location: Canada
Posts: 4,267
Quote:
Originally Posted by Findm-Keepm View Post
Yes, we modded ours - originally it was ultrasonic only, but a Zenith service seminar in 79 or 80 gave up the kit number for the IR mod, which also included the instructions to mod it to verify drive signals on the early System IIIs. They demo'ed it at the service seminar connected to an oscope, for purely visual means. We used it autonomously and rarely connected it to anything. Don't leave it on - the battery dies quickly.
I reckon the scope connection would be good for remote tuning or determining frequencies. Could come in handy for getting one of my 6-rocker XL-100 remotes working properly with my Heathkit GR-2000. At least one frequency already matches what the Heathkit expects for the same function.
Reply With Quote
  #4  
Old 06-06-2017, 04:51 AM
Findm-Keepm's Avatar
Findm-Keepm Findm-Keepm is offline
Followin' the Rules...
 
Join Date: Jun 2007
Posts: 2,857
Quote:
Originally Posted by Jon A. View Post
I reckon the scope connection would be good for remote tuning or determining frequencies. Could come in handy for getting one of my 6-rocker XL-100 remotes working properly with my Heathkit GR-2000. At least one frequency already matches what the Heathkit expects for the same function.
Or for finding bad cork/rubber damper pads in the rod-type remotes. Glue or pad dries out, the pad falls off, and gets in the way, detuning the remote. Saves having to open the remote if nothing is wrong with it.

Somewhere in my older Zenith service lit is another circuit for a remote tester and an ultrasonic signal generator, 1969 or 1970..

The Brits published a magazine called "Television" that had service info - they also published a project for a tester, both IR and ultrasonic. This was in late 1987 or so. I bought the issue in London when I was visiting. It used the mic and diode as inputs to a Schmitt trigger, squaring up things. A frequency discriminator was used in the ultrasonic side, and a dual LED in the IR side. Same issue had info about checking the IR remote oscillators with an AM radio (most resonator/oscillators operated at either 455Khz or 500KHz...). ..
__________________
Brian
USN RET 22YRS (Avionics/Cal)
CET-Consumer Repair and Avionics ('88)
"Capacitor Cosmetologist since '79"

When fuses go to work, they quit!
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:27 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.