Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early Color Television

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 03-12-2017, 03:21 PM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
Manual disables the remote, Automatic enables the remote. It is a fail safe insace a relay sticks, and it also allows power savings on vacations, etc.

It was not uncommon for Zenith to shuffle the remote rods arround or use different ones on different years/models. Do any of the remote buttons activate any relays on the set?

I generally troubleshoot remotes by plugging in the set's mike to a scope to confirm the mike works. Then I try to follow that signal through the remote chassis with the scope. I often use an audio generator that can go up to 20-30KHz to replace the mike while signal tracing....You can also dial the signal gen around to see if the relays work, but happen to be tuned to different freqs. If it works on different freqs you can compare them to the ones in the hand unit and see which functions on the set best match the rods and tune those functions to those rods (and later reshuffle the rods the buttons operate so that the labels match).

The fine tuning mech in your tuner may need work.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
  #2  
Old 03-12-2017, 04:19 PM
VA561's Avatar
VA561 VA561 is offline
VideoKarma Member
 
Join Date: Apr 2010
Location: norfolk,virginia
Posts: 216
Channel lower button works. Volume/on-off button does not work. Sound (mute) button works. Channel higher button does not work.
Reply With Quote
  #3  
Old 03-12-2017, 04:34 PM
Findm-Keepm's Avatar
Findm-Keepm Findm-Keepm is offline
Followin' the Rules...
 
Join Date: Jun 2007
Posts: 2,857
When one or two functions on ultrasonics fail, it is usually the remote - the rods corrode, the mounts deteriorate, or the striker has deformed. Got another remote to try? If not, take a close look at the rods and mounts in your remote. Post pix if you can - I've seen just a speck of encrusted dirt kill a function on the clicker remotes.

3/4ths of your remote receiver are known good if you have any functions working.
__________________
Brian
USN RET 22YRS (Avionics/Cal)
CET-Consumer Repair and Avionics ('88)
"Capacitor Cosmetologist since '79"

When fuses go to work, they quit!
Reply With Quote
  #4  
Old 03-12-2017, 05:53 PM
VA561's Avatar
VA561 VA561 is offline
VideoKarma Member
 
Join Date: Apr 2010
Location: norfolk,virginia
Posts: 216
Took remote apart to inspect and clean. Pictures are before I used contact cleaner to carefully clean any gunk out. Inside looked surprisingly clean. After cleaning it still does the same thing. I noticed inside the remote section there looks to be a possible sensitivity adjustment? Have noticed when I hit the channel higher button, I hear nothing in the remote section as I do with all of the other buttons. Volume/on-off button makes a sound in the remote section like the rest of the good buttons but does nothing.
Attached Images
File Type: jpg sc4003.jpg (97.0 KB, 28 views)
File Type: jpg sc4002.jpg (49.4 KB, 25 views)
File Type: jpg sc4001.jpg (88.2 KB, 37 views)
File Type: jpg remote adjust.jpg (43.8 KB, 30 views)
File Type: jpg sc4004.jpg (97.1 KB, 38 views)

Last edited by VA561; 03-12-2017 at 06:01 PM.
Reply With Quote
  #5  
Old 03-12-2017, 06:04 PM
Findm-Keepm's Avatar
Findm-Keepm Findm-Keepm is offline
Followin' the Rules...
 
Join Date: Jun 2007
Posts: 2,857
Agree on the cleanliness - spotless! Be careful with any adjustments - I'd follow the alignment procedure for the remote chassis - do you have a Zenith manual for the remote chassis? Sams is awful with their alignment procedures for remote chassis (at least for RCA and Magnavox...).

If that is indeed a sensitivity control - be careful - too sensitive and some features will quit working, as the gain is increased to the point of saturating the amp, and causing the control pulses to widen. Also, too much sensitivity can cause it to respond to other sounds - keys jingling on a key chain, the phone, etc.

Cheers,
__________________
Brian
USN RET 22YRS (Avionics/Cal)
CET-Consumer Repair and Avionics ('88)
"Capacitor Cosmetologist since '79"

When fuses go to work, they quit!
Reply With Quote
Audiokarma
  #6  
Old 03-12-2017, 06:27 PM
VA561's Avatar
VA561 VA561 is offline
VideoKarma Member
 
Join Date: Apr 2010
Location: norfolk,virginia
Posts: 216
Don't have the zenith manual for the remote chassis. You would think that if it was a sensitivity issue that none of the buttons would work or all would work.
Reply With Quote
  #7  
Old 03-12-2017, 06:38 PM
reeferman's Avatar
reeferman reeferman is offline
VideoKarma Member
 
Join Date: Jun 2004
Location: St. Louis
Posts: 593
If you lose your Zenith tuning fork remote...

and want to see if the remote is working, get out your key chain and shake vigorously in front of the set. If the tuner or any control moves, you can bet the rest of the functions work. At least that was the way it was in the 60's when we serviced the things. Great way to change the channels at home if the remote isn't handy.

Last edited by reeferman; 03-12-2017 at 06:50 PM.
Reply With Quote
  #8  
Old 03-15-2017, 07:16 PM
Jon A.'s Avatar
Jon A. Jon A. is offline
Don't mess with Esther.
 
Join Date: Jun 2013
Location: Canada
Posts: 4,267
Quote:
Originally Posted by Findm-Keepm View Post
If that is indeed a sensitivity control - be careful - too sensitive and some features will quit working, as the gain is increased to the point of saturating the amp, and causing the control pulses to widen. Also, too much sensitivity can cause it to respond to other sounds - keys jingling on a key chain, the phone, etc.

Cheers,
No kidding. That reminds me of what happened in the storage room with my Sanyo. I don't recall exactly what I was doing but it caused a pile of remotes to take a spill, and boom, the TV came on. I checked the remotes I knew I had tried batteries in, none had any.
Reply With Quote
  #9  
Old 03-16-2017, 06:48 AM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
Quote:
Originally Posted by Jon A. View Post
No kidding. That reminds me of what happened in the storage room with my Sanyo. I don't recall exactly what I was doing but it caused a pile of remotes to take a spill, and boom, the TV came on. I checked the remotes I knew I had tried batteries in, none had any.
Response to randomly generated ultrasonic tones is the nature of the beast....My SC600 Avanti comes on by it's self any time I vacuum in the room it is in.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:40 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.