Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 02-27-2017, 02:18 AM
EdKozk2 EdKozk2 is offline
Tinker
 
Join Date: Mar 2014
Location: Elkhorn, WI
Posts: 542
Hi Crist,
You said you heard clicking? Does it sound more like ticking, intermittent or continuous? I ask because if you stuffed the old doorknob with a modern ceramic or mica cap, you may have arcing between the cap leads. When I repaired my Admiral last fall I used a 15kv cap as a substitute for the old doorknob. When I first tested the set I would hear ticking. Lowering the brightness would increase the amount of ticking, increasing would decrease the amount. I had to operate the set on its' side and in darkness to see the source of the ticking. Turned out the gap between the capacitor leads right at the body of the cap needed a greater gap. The proper dressing of the leads solved the problem I had. I didn't reuse or stuff the old doorknob. I mounted the cap under the chassis.
Ed
Reply With Quote
  #2  
Old 02-27-2017, 10:59 AM
Crist Rigott Crist Rigott is offline
VideoKarma Member
 
Join Date: Oct 2015
Location: Waxahachie, TX
Posts: 1,519
Quote:
Originally Posted by EdKozk2 View Post
Hi Crist,
You said you heard clicking? Does it sound more like ticking, intermittent or continuous? I ask because if you stuffed the old doorknob with a modern ceramic or mica cap, you may have arcing between the cap leads. When I repaired my Admiral last fall I used a 15kv cap as a substitute for the old doorknob. When I first tested the set I would hear ticking. Lowering the brightness would increase the amount of ticking, increasing would decrease the amount. I had to operate the set on its' side and in darkness to see the source of the ticking. Turned out the gap between the capacitor leads right at the body of the cap needed a greater gap. The proper dressing of the leads solved the problem I had. I didn't reuse or stuff the old doorknob. I mounted the cap under the chassis.
Ed
Ed,
The clicking I heard was as if a mica cap goes bad. I was touching the ceramic cap on the big coil on the tuner (I forget the name) and got the clicking sound. It also could be coming from somewhere else.

I didn't have the door knob cap installed at all. I'm still waiting for them to arrive. Good info though. Thanks.

BTW, the HV on this TV is listed as only 7.5Kv so the possibility of arcing between the 20Kv leads should be reduced by a lot.
Reply With Quote
  #3  
Old 02-28-2017, 12:23 AM
Crist Rigott Crist Rigott is offline
VideoKarma Member
 
Join Date: Oct 2015
Location: Waxahachie, TX
Posts: 1,519
I worked on the Horizontal and Vertical sections today. They have been recapped and recarbed for the most part. I forgot to take a picture of my progress before starting this post.

Here is a picture of what I was working with. Caps and resistors seemingly wired "in the air"!


Anyway here is a picture of the picture as of tonight. Some change. Getting better. I think the audio will have to be aligned before I get any audio that matches the CRT.



Next up the Sync Separator and on to the Audio section.
Reply With Quote
  #4  
Old 02-28-2017, 11:27 AM
Crist Rigott Crist Rigott is offline
VideoKarma Member
 
Join Date: Oct 2015
Location: Waxahachie, TX
Posts: 1,519
Here is a after picture of what was worked last night.

Reply With Quote
  #5  
Old 03-02-2017, 12:39 AM
Crist Rigott Crist Rigott is offline
VideoKarma Member
 
Join Date: Oct 2015
Location: Waxahachie, TX
Posts: 1,519
I finished with the Sync Separator and audio sections. All sections are done except the IF strip and tuner. I still have to go through the back chassis control pots to clean them up and check them.

Here is a picture of the completed Sync section.


And the audio section:
Reply With Quote
Audiokarma
  #6  
Old 03-02-2017, 11:31 PM
Crist Rigott Crist Rigott is offline
VideoKarma Member
 
Join Date: Oct 2015
Location: Waxahachie, TX
Posts: 1,519
I did the IF strip today. The chassis is basically been re-capped etc.



I installed some Y2 safety caps and one of them went to the switched AC power from the on-off switch to the transformer. Remember when I redid the volume pot? The one wire was chaffed pretty good on the chassis and I cut out that section and installed about a 4 inch piece of new wire under the chassis. That wire was the one that needed the safety cap. I installed a terminal strip and spliced a wire into the switched AC power and ran it to the terminal strip. I then installed the safety cap.






I'm in the middle of cleaning, lubing, and checking the back panel pots. When those are done, then the speaker and mount gets cleaned up and re-installed.

BTW, I have a APB for a electrical dual coil Ion Trap in the classifieds. Mine came with a resistor across the leads and a Dual PM Ion Trap.

Last edited by Crist Rigott; 03-02-2017 at 11:37 PM.
Reply With Quote
  #7  
Old 03-03-2017, 08:01 PM
miniman82's Avatar
miniman82 miniman82 is offline
First Light: 1952-2011
 
Join Date: Jun 2009
Location: Great Mills, MD
Posts: 4,183
Yours for the cost of postage.


Attached Images
File Type: jpg IMG_1006.jpg (57.9 KB, 99 views)
__________________
Evolution...
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:57 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.