![]() |
|
|
|
#1
|
|||
|
|||
|
#2
|
|||
|
|||
|
Good news to report coming up. Stay tuned.
|
|
#3
|
|||
|
|||
|
I got a new 21FP4C rebuilt CRT. A big thank you to El Predicta who donated the CRT for this project. He also donated a spool of solid 20awg white wire. Thank you very much for your generosity!
Here are a few pictures of the CRT. ![]() ![]() I tested the CRT on my B&K 467. It checked out at 1.7. ![]() And the Life Test showed a drop from 1.7 to 1.65. ![]() Here is a picture of the straight gun. Yeah, I have to glue the base back on. ![]() Again a big shout out to El Predicta! Thank you. Last edited by Crist Rigott; 12-08-2016 at 10:58 AM. |
|
#4
|
|||
|
|||
|
#5
|
|||
|
|||
|
I started working on re-stuffing the E-Caps. The first one is the multi sectioned C43. It has a 20uf 150V, 10uf 150V, and a 100uf 25V.
![]() After removing the cardboard cover, this is what I found: ![]() I was a bit taken back but decided that what I should use is what the schematic and parts list calls for. What do you think? |
| Audiokarma |
|
#6
|
|||
|
|||
|
I'm in the middle of re-stuffing the E-Caps. I used my heat gun to heat up the cardboard cover and pulled it off the can. I then cleaned off all the black tar/wax from the capacitor. I then made some marks 3/8 inch up from the base of the cap. This is where I'll make the cut using my band saw. I cut each cap on the marks then dug out the caps innards. Cleaned up the bases and on the 2 single 200uf 150V caps I drilled 1/16 hole in the center and the other one near one of the mounting lugs. I'll run the wires through the holes and solder them to the correct lug.
I then took some 1" thin walled PVC tube and cut 1 inch lengths and trued up one end which was then marked. After the bases were cleaned up and de-burred and the PVC tube de-burred and cleaned up, the marked end were epoxied into their bases. the excess epoxy was then wiped off and the assembly was cleaned using rubbing alcohol and then the new caps will be wired in. ![]() ![]()
Last edited by Crist Rigott; 12-10-2016 at 11:43 PM. |
|
#7
|
|||
|
|||
|
Quote:
. |
|
#8
|
|||
|
|||
|
That would be kinda hard, seeing it's been cut in half. anyways I don't have any way to measure it.
|
|
#9
|
|||
|
|||
|
I restuff my cans in much the same way. The only thing different is, instead of the PVC pipe, I use the thin aluminum salvaged from a beverage can.
I cut the can apart with kitchen shears and roll the metal up as a sleave, then I use silicone sealant to hold it all together. |
|
#10
|
|||
|
|||
|
Quote:
The label made on a spirit duplicator shows some real class. Reminds me of school days, where some weekly tests were ran off on them. The cap has a Sentinel part number from 1953. ![]() I would use 22mfd for the 10, 47 for the 20 @250 volts and 100 @160 volts for the 100 section. BTW, Is there any truth to the theory that operating too high of a voltage rated 'lytic on lower voltage, IE a 450 volt cap at 150 volts, that they never seem to form properly, or just another urban tale.
|
| Audiokarma |
|
#11
|
|||
|
|||
|
That is quite normal. Capacitor manufacturers would often use a can that was already stamped and stuff whatever they needed into it when they knew they were going to put a cardboard sleeve around it. I have seen it several times.
|
|
#12
|
|||
|
|||
|
I was thinking along the same lines. Remember this cap has never been installed, it is a part of the kit.
|
|
#13
|
||||
|
||||
|
Quote:
Just the cap manufacturer "reclaiming" perfectly usable scrap from a previous production run, and using it where it presumably wouldn't be noticed. |
|
#14
|
||||
|
||||
|
Keep in mind that maximum contrast on these old sets is a bit of an illusion that relies heavily on the ambient lighting in the viewing room. Of course the screen can never get darker than it is when it's off for a given ambient light level. So considering the relatively bright room lighting in your below picture, I'd say your set is putting out about the best contrast it's capable of. The modern set next to it likely has a darker screen filter, yet to me it looks more washed out than your Tech Master. Also remember that the contrast of the old program material was not all that consistent. Your set has a darn good picture with your DVD test pattern on it, so just be careful that you don't go chasing rainbows in an attempt to correct for a lousy picture that your OTA converter box may be responsible for.
Last edited by Kevin Kuehn; 01-30-2017 at 11:38 PM. |
|
#15
|
|||
|
|||
|
Kevin,
Thanks for those thoughts. You are right about chasing rainbows! What I eneded up doing is to eliminate R109, thus reducing the lowest value the pot can go to 93 ohms instead of 93 + 39 = 142 ohms. This gives me acceptable contrast when watching some of the older programs on MeTV. The contrast control is almost but not quite at its full stop. I live with it. What really helped was putting the 3.3K across the 5K pot to get the listed 2K. This gives me a little more dial to adjust the contrast. Working on how to do the cabinet right now. I'm going back and forth on what I want to do. Once I settle on that then I can "lock" down the CRT mounting. BTW, I've gone to a 17" CRT. I'm using a NOS rebuilt RCA 17LP4B. Thanks to El Predicta here on the forum. The reason is because I'm going to use the "sleeve" to control the width and when I do that, the HV goes down. So I thought the 17" CRT would handle the reduced HV better and thus give me better service for the life of the TV. |
| Audiokarma |
![]() |
| Thread Tools | |
| Display Modes | |
|
|