![]() |
|
|
|
#1
|
||||
|
||||
|
These RCA's can be undone by stupid stuff, most heat-related. I just got done with a CTC16 where a wire run on top of PW700 next to a 6GU7 tube socket pin, was arcing only under full AC power and smoking the cathode resistor. Visually, the resistor was the prime suspect until seeing the little flashing arc under the socket. The resulting potpourri of reeked of classic RCA fly arcing and made the set's owner think his NEW flyback just burned up.
So all looks well on that oscillator PW, even the tube and socket? Its just not normal for an synchroguide oscillator to NOT run. The coils could not have been adjusted out so far as to shut it down I suppose. Maybe Im grabbing at straws here but see what is external to the circuit, causing issues DC voltages are coming *TO* the stakes. on the osc PWB. Start with resistance at D, to see if maybe a shorted AFC diode (which are over on the vert PWB) should be very high like 780 K ohm. H-275 vdc, A -386 vdc, F-6.3 vac, D - zero dc and 40v p-p ac, G and E both close to 260 vdc. If any cap gets leaky like C604, C605 and C606 its curtains. If I was not out of VK memory, Id post the schematic for clarity.
__________________
"When resistors increase in value, they're worthless" -Dave G |
|
#2
|
||||
|
||||
|
Quote:
How are the traces? I've seen open and or crappy traces on that era of board...If they look bad or voltages are not getting places I tend to reflow/add new solder to the traces.
__________________
Tom C. Zenith: The quality stays in EVEN after the name falls off! What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4 |
|
#3
|
|||
|
|||
|
FYI, I have a Photobucket account. It is now rubbish, full of delays, popups, begging for money etc. Many times I just cannot even use it.
Just sayn' (but I guess I get what I am payn' for...) |
|
#4
|
||||
|
||||
|
Quote:
Flickr its great for posting numerous pictures of a restore and makes sense when you have lots of photos, instead of one-off posts like this, where it is kludgy to use.
__________________
"When resistors increase in value, they're worthless" -Dave G |
|
#5
|
||||
|
||||
|
Flickr acts the same on all my devices....VK's upload/image size limits prevent me from uploading %99.8 percent of the pictures I have, and a hosting site has proved easier for me to implement/use than resizing my images and hosting them on VK.
It is a bit less clunky if you run adblock plus in your browser (I still get popups occasionally). My photobucket account is effectively dead to me....Once I (rapidly) ran out of storage capacity and they started prompting me to buy more, I switched to flickr and have not looked back....Well I do occasionally go there to post an old photo still on the bucket.
__________________
Tom C. Zenith: The quality stays in EVEN after the name falls off! What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4 |
| Audiokarma |
|
#6
|
||||
|
||||
|
Call me late to the party, but Dad's (incomplete) Sams for the CTC11 is marked up pretty good. There's this (not in Dad's handwriting) - HOT cherries, check Osc tube filament for 6V. Was half. No corrective action listed.
And plenty about contrast, swapping guns to check CRT, and other non-germane stuff. PF Reporter also had an instance... http://www.americanradiohistory.com/...rch=%226dq5%22 Me, no experience earlier than a CTC12, so no real help beyond that note..
__________________
Brian USN RET 22YRS (Avionics/Cal) CET-Consumer Repair and Avionics ('88) "Capacitor Cosmetologist since '79" When fuses go to work, they quit! |
|
#7
|
|||
|
|||
|
Gotta wonder at this point if either of the windings might have shorted turn(s), dragging down the Q enough to keep the oscillator from starting.
|
![]() |
| Thread Tools | |
| Display Modes | |
|
|