Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 11-26-2016, 11:56 AM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
A resistor in that position can act as a slow blow fuse if a filter cap shorts hard to ground. Before blowing it protects the power transformer from over current. Basically it acts as a shock absorber.
Reply With Quote
  #2  
Old 11-26-2016, 06:59 PM
Doug66 Doug66 is offline
VideoKarma Member
 
Join Date: Sep 2014
Posts: 166
Hey Guys,
Thanks for the replies.
R106 was replaced when I 1st recapped the set. The original sand coated resistor was still there, so it had to go. I just checked, and the replacement still reads 65 ohms.

As far as the filter caps, I have double and triple checked my work to make sure those are installed correctly. A one point I even took out the new replacements and installed another et of new replacements just to make sure one was not shorted.

I also checked the socket on the 6BQ6. Only pins chowing continuity to ground are pins 2 and 7. I also disconnected one end of C86 to make sure it was not shorted and pulling the voltage on pin 4 down.
Reply With Quote
  #3  
Old 11-26-2016, 07:21 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
What about resistor R100 (47 0hm)?

You mentioned that cap C3 which is in parallel with it, had 'fried' at one time.
Reply With Quote
  #4  
Old 11-26-2016, 10:12 PM
Doug66 Doug66 is offline
VideoKarma Member
 
Join Date: Sep 2014
Posts: 166
R100 (47ohm) has been replaced. Yes, C3 did fry at one time when I disconnected the 340V line from pin 8 of the flyback. However, that did bring the voltage back to normal.

Explain this to me please. if I'm reading the schematic right, the 340V going thru R100 and C3 should be producing the 330V source. It's not. My 330V source is coming off pin 3 (blue wire) of the yoke. I disconnected both horiz wires from the yoke (pins 3 and 1 of yoke. Pin 1 goes to pin 7 of the flyback), and my 340 volts returned to normal. However I had no 330V. I measured the blue wire (pin 3) which was hanging in mid air, and it had 330V on it. Co

Connecting the blue wire back to where the 330V source should be put voltage on all circuits calling for 330V, but too low. That's when I disconnected everything connected to the 330V and found the problem seeming to be at pin 4 of the 6BQ6.
Reply With Quote
  #5  
Old 11-27-2016, 04:52 PM
wa2ise's Avatar
wa2ise wa2ise is offline
VideoKarma Member
 
Join Date: Dec 2002
Location: USA
Posts: 3,147
Quote:
Originally Posted by Kevin Kuehn View Post
A resistor in that position can act as a slow blow fuse if a filter cap shorts hard to ground. Before blowing it protects the power transformer from over current. Basically it acts as a shock absorber.
It also makes life a little easier for the vacuum tube rectifier. Lower peak currents due to the filter cap recharging between full wave cycles at 120Hz. You can kill a rectifier tube if you have too much filter cap and too low source impedance on it. SS diodes are much more forgiving here.
__________________
Reply With Quote
Audiokarma
  #6  
Old 11-27-2016, 09:07 PM
EdKozk2 EdKozk2 is offline
Tinker
 
Join Date: Mar 2014
Location: Elkhorn, WI
Posts: 542
Hi Doug,
I'm assuming you recapped the whole set. Looking at the entire schematic,did you check what circuit variation your set has. If you use the dotted line wiring changes, make sure your width coil T7 is grounded on one end. The other end goes to pin 5 of the flyback only. The blue wire/ pin 3 of the deflection coil only goes to your 330 volt source junction of R100,R105,C1 and C3. If you didn't notice, the plate circuit of the video output tube 12BH7 is also connected to the 330 volts. Are you getting a 525v, B+ BOOST voltage at pin 10 of the CRT ? Check C85 and C84 the horizontal feedback
caps if your set uses them. Make sure C5 and C6 connected to the red lead of the vertical output transformer didn't short when you cooked C3. A short there would load down the B++ and flyback.
Ed
Reply With Quote
  #7  
Old 11-28-2016, 05:42 PM
Doug66 Doug66 is offline
VideoKarma Member
 
Join Date: Sep 2014
Posts: 166
Hey Guys,

Here is what I have come up with:
C87 & C88 were replaced when I recapped the set.
Also the 6W4 damper and 6BQ6 are new.
On the 6BQ6, K and G1 are fine on voltage. In fact G 2 which is pin 8, and the one in question actually has 130V only 20V low despite the big drop in the B+.

I do have hi voltage. Plate of 12BH7 SB 290V and I have 241.

R96 and 97 have also been replaced as well as C2.

EdKozK2, yes my set does use the dotted line circuit and my width coil does go between pin 6 of the flyback and ground (pin 6). B+ boost voltage on pin 10 of CRT only has 435V.

Here is where I get confused. The red wire of the yoke goes to the 330V source. On my set, that wire IS the 330 source. If I disconnect that wire and leave it hanging in mid air, it still has 330V on it, and there is nothing on the negative side of C3 and the 47 ohm.
Reply With Quote
  #8  
Old 11-28-2016, 06:12 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by Doug66 View Post

Here is where I get confused. The red wire of the yoke goes to the 330V source. On my set, that wire IS the 330 source. If I disconnect that wire and leave it hanging in mid air, it still has 330V on it, and there is nothing on the negative side of C3 and the 47 ohm.
Do you also have 330V on the yokes blue wire when you disconnect the red? Ed just mentioned that only the blue yoke wire should be connected to the 330V source. Of course if the blue is connected and you disconnect the red you will also measure 330v on the red, because it's a very low resistance path though that yoke winding to the blue wire. Or are you saying that the blue and red yoke wires are reversed on your set? Do you measure 340v at the top of C3 and R100?

Last edited by Kevin Kuehn; 11-28-2016 at 06:20 PM.
Reply With Quote
  #9  
Old 11-28-2016, 08:10 PM
Doug66 Doug66 is offline
VideoKarma Member
 
Join Date: Sep 2014
Posts: 166
Yes, with the red disconnected, I actually have 375V on the blue and at the top of C3 and R100.

Let me throw this at you. I replaced the vertical output transformer 1st thing with a Stancor replacement. According to the Sams, you have to change a couple of leads. I thought I did that correctly, but if I made a mistake there, could THAT be dragging my B+ down? Now I just disconnected all 4 of the vert output transformer leads, but the B+ was still too low, so I reconnected them.
Reply With Quote
  #10  
Old 11-28-2016, 09:24 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
I don't have a full schematic so I'm a little in the dark trying to see the big picture.
Reply With Quote
Audiokarma
  #11  
Old 12-04-2016, 08:41 PM
Doug66 Doug66 is offline
VideoKarma Member
 
Join Date: Sep 2014
Posts: 166
Would the horizontal ringing also cause the reduced vertical. I'm still wondering if I hooked up the replacement vertical output transformer right. The Sams gives instructions in the parts list and they are confusing.
It says: Connect blue lead to transformer plate.
Connect green lead of transformer and Boosted B+ to brown lead of
yoke.
remove green lead from yoke from it's present terminal and connect
to red lead of transformer.
It doesn't say anything about where the yellow lead goes. I assume it still goes to the 340V.
Those instructions are confusing. Here are two parts of the schematic showing where all leads of the original transformer went and also where the brown wire off the yoke went.
The original green lead went to the brown lead of the yoke. The new instructions say do that as well as put the boosted B+ to this lead. If I read the schematic right, the original red lead is the boosted B+. That lead goes thru R76, R77, then thru a 2.2 med (R80) and onto pin 10 of CRT at 525V.

If I've got this transformer wired in wrong, could that be pulling down my B+? However if I disconnect all leads of the vert transformer, B+ is still pulled down.
Attached Images
File Type: jpg IMG_0004 (3).jpg (58.6 KB, 10 views)
File Type: jpg IMG_0003 (5).jpg (84.7 KB, 12 views)
Reply With Quote
  #12  
Old 12-04-2016, 09:48 PM
Doug66 Doug66 is offline
VideoKarma Member
 
Join Date: Sep 2014
Posts: 166
I've been doing some more checking in the damper circuit. Pin 3 has 418V. The Sams does not give a voltage for this pin. It goes to a .1 which should have the 340 B+ on the other side.
Pin 5 should have 330V. My VOM showed a small arc when I touched the lead to it but would read nothing. I got out my VTVM which only goes to 300V DC. I figured 30V wouldn't overload it too much. It pegged the left side of the scale meaning a negative voltage was present. I switched it to DC- , then the needle pegged the right side of the scale.

I then reversed the leads on my VOM to read negative, and it shoved an overload.

Pin 5 goes to pin 4 of the flyback.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:11 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.