Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early Color Television

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 07-17-2016, 04:40 PM
wiseguy wiseguy is offline
VideoKarma Member
 
Join Date: Jun 2002
Posts: 382
you should Discharge the HV from the CRT completely before testing on a CR-31, this would cause Erratic Testing, the pop you heard could have been a HV discharge to chassis Ground since its been modified for a newer tube, I went thru this on my ctc-4 before the CRT got rebuilt when hawkeye was in business, there is also some mods in the Gun Drive Circuit to make these newer tubes "run" correctly, color Temp is a bit different
Good Luck!

Last edited by wiseguy; 07-17-2016 at 04:47 PM.
Reply With Quote
  #2  
Old 07-17-2016, 05:13 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
The loud pop could easily have been a HV arc from the anode button to the shield (where somebody has made a big cutout in the shield). In fact, in your 5th photo there's what looks like an arc track from the button to the shield.

"rejuvving" the jug should be the absolute last resort.
Reply With Quote
  #3  
Old 07-17-2016, 07:26 PM
Phil Nelson's Avatar
Phil Nelson Phil Nelson is offline
VideoKarma Member
 
Join Date: Jan 2006
Posts: 4,030
Definitely do not rejuvenate the CRT at this point. Too easy to kill the tube, and what you're seeing on the screen may be normal for a CTC-4 that's chock full of bad caps. A working television will tell you more about a CRT's condition than any tester.

I agree with old_coot88, that pop sound could be arcing, and the cutout in the CRT metal retaining ring is an obvious place to look. If you run the TV briefly in a completely dark room, you might even see the zap occur along that dark track seen in the photo.

When I installed a glass CRT in my set, I made a smaller cutout in the ring, but I also covered the nearby edges with cambric insulating tape rated for 90KV. More about all that in:

http://antiqueradio.org/RCACTC-4ColorTelevision.htm

You are right to think of this as a long term project. Be patient and it will all get done. CTC-4s don't come along very often, so enjoy working with this one while you can.

Have fun!

Phil Nelson
Phil's Old Radios
http://antiqueradio.org/index.html

P.S. What's in the little metal project box? Looks like a relay and a tube on top . . . ?
Reply With Quote
  #4  
Old 07-17-2016, 07:38 PM
SwizzyMan's Avatar
SwizzyMan SwizzyMan is offline
Restoring an admiral c322
 
Join Date: Apr 2015
Location: Side Lake Mn
Posts: 886
Quote:
Originally Posted by Phil Nelson View Post
Definitely do not rejuvenate the CRT at this point. Too easy to kill the tube, and what you're seeing on the screen may be normal for a CTC-4 that's chock full of bad caps. A working television will tell you more about a CRT's condition than any tester.

I agree with old_coot88, that pop sound could be arcing, and the cutout in the CRT metal retaining ring is an obvious place to look. If you run the TV briefly in a completely dark room, you might even see the zap occur along that dark track seen in the photo.

When I installed a glass CRT in my set, I made a smaller cutout in the ring, but I also covered the nearby edges with cambric insulating tape rated for 90KV. More about all that in:

http://antiqueradio.org/RCACTC-4ColorTelevision.htm

You are right to think of this as a long term project. Be patient and it will all get done. CTC-4s don't come along very often, so enjoy working with this one while you can.

Have fun!

Phil Nelson
Phil's Old Radios
http://antiqueradio.org/index.html

P.S. What's in the little metal project box? Looks like a relay and a tube on top . . . ?
Thanks Phil! I'll try and keep watch on that area suspect to arcing. The little project box is actually a soft start module. It lets the tubes fully heat up before applying any voltage to them. The same concept is shared on your CTC-7, but this was one of the modifications the previous owner installed. I think its pretty nifty!
__________________

Admiral C322C2 Regent (Restoring)
RCA CTC-7 Pensbury (Restored)
RCA CTC-5 Westcott (Restored)
CRA CTC--4 Director 21 (Restoring)
Reply With Quote
  #5  
Old 07-17-2016, 08:31 PM
SwizzyMan's Avatar
SwizzyMan SwizzyMan is offline
Restoring an admiral c322
 
Join Date: Apr 2015
Location: Side Lake Mn
Posts: 886
Cant tell if this is a HOT cathode current meter or what. I dont think it is since the meter only has a range of 10 MA and normal cathode current is atleast 100MA.
Attached Images
File Type: jpg DSC_1012.jpg (55.3 KB, 85 views)
__________________

Admiral C322C2 Regent (Restoring)
RCA CTC-7 Pensbury (Restored)
RCA CTC-5 Westcott (Restored)
CRA CTC--4 Director 21 (Restoring)
Reply With Quote
Audiokarma
  #6  
Old 07-17-2016, 09:38 PM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
Quote:
Originally Posted by SwizzyMan View Post
Cant tell if this is a HOT cathode current meter or what. I dont think it is since the meter only has a range of 10 MA and normal cathode current is atleast 100MA.
It could be a cathode current meter with the appropriate shunt resistance in parallel with it to scale the current it receives to the appropriate range...
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
  #7  
Old 07-17-2016, 09:57 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
Quote:
Originally Posted by SwizzyMan View Post
Cant tell if this is a HOT cathode current meter or what. I dont think it is since the meter only has a range of 10 MA...
That meter is one milliamp full-scale. So it's probably wired to measure the HV regulator current. If it's measuring H.out cathode current, it'll have a low value shunt across it.
Quote:
...and normal HOT cathode current is at least 100MA.
Normal H.out cathode is closer to 200 ma.
Reply With Quote
  #8  
Old 07-18-2016, 07:11 PM
SwizzyMan's Avatar
SwizzyMan SwizzyMan is offline
Restoring an admiral c322
 
Join Date: Apr 2015
Location: Side Lake Mn
Posts: 886
I wonder if the CTC-4 has those pesky HV issues like the CTC-5 does? I really hated dealing with that in my 5. And how is its performance? Hopefully better than my 5 too.
__________________

Admiral C322C2 Regent (Restoring)
RCA CTC-7 Pensbury (Restored)
RCA CTC-5 Westcott (Restored)
CRA CTC--4 Director 21 (Restoring)
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:49 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.