![]() |
|
|
|
#1
|
||||
|
||||
|
Better quality TVs had three IF stages (like my Dumont RA-103), or even four (like my RCA CT-100). More IF stages means more amplification of the incoming signal, resulting in greater sensitivity (ability to pull in weak, far-away stations). A TV with only two IF stages would only have worked well in a metro area with nearby stations.
Sensitivity per se is not such a big deal nowadays, when many collectors feed their restored TVs from a DVD player or whatnot, with a nice strong signal. The number of IF stages can be interpreted as a sign of overall quality, however. If the manufacturer skimped in that area, they may have skimped in others, too. Phil Nelson Phil's Old Radios http://antiqueradio.org/index.html |
|
#2
|
|||
|
|||
|
Quote:
Thanks for the explanation. I can see where if they scrimped here they could scrimp there kind of a deal. When I'm done I'll for sure include some videos of the picture and sound quality. Again thanks and I enjoy reading over your restorations both radio and TV. |
|
#3
|
|||
|
|||
|
Here some more pics. I cleaned the chassis with some mild dish washing detergent. It wasn't real dirty and it cleaned up pretty well.
I checked the tubes and some are weak and some are very weak! I then got to work on making and ID on every capacitor and resistor and comparing it with the schematic and parts list. There were some discrepancies but nothing real major. I use a small block of masking tape and mark each component. While doing this I check the schematic and parts list. I then make the document changes in red ink. I also drew out the 2 tube configuration for the listed 6T8 tube. Besides using 2 tubes, there were a few resistors and capacitors in the chassis that weren't in the schematic. I'll update my parts lists accordingly so I get my order right. I'll draw up the new configuration and I'll post it side-by-side with the schematics so we can see what the changes were. ![]() ![]()
Last edited by Crist Rigott; 12-04-2016 at 01:28 AM. |
|
#4
|
|||
|
|||
|
Quote:
I wonder what the reason was?
|
|
#5
|
|||
|
|||
|
I wondered about that little selenium too, thinkin' maybe it was a neg.bias supply. But couldn't spy it in the schematic.
|
| Audiokarma |
|
#6
|
||||
|
||||
|
CT-100 (and TRK-12) have FIVE IF stages!
Yes, more gives more gain.. BUT ... it also allows a more sharply tailored bandpass curve with a very sharp 4.2 MHz cutoff. Doing the sharp bandpass edges cuts overall gain. |
|
#7
|
|||
|
|||
|
The last day or so was spent taking inventory of what parts are needed and making a list and where to get them from. Some I had "in stock" while others will be ordered from Just Radios and Digikey. I've decided to bump up the 1/2W to 1W, the 1W to 2W and the 2W to 3W. Some of the 2W resistors seemed a bit discolored and heat stressed so those 3 will be replaced with 5W (R70, R71, R73). There was one resistor clearly bad. It had split open due to excessive heat. It is R76 a 470 ohm 2W resistor. This will be replaced with a 470 ohm 10W resistor the local parts house had in stock. It will still fit nicely in the chassis.
I'm using the taller, slender Nichicon 105c E-Caps so they'll fit into the cans. There are 2 cans with 3 each caps in them ![]()
Last edited by Crist Rigott; 12-04-2016 at 01:30 AM. |
|
#8
|
|||
|
|||
|
While I wait for the parts to arrive I'd like to clean up the HV cage. Never having done a TV before with a flyback I could use some guidance. I want to clean this up and of course replace the 2 680K 2w resistors with 2 680K 3w resistors and the .00047 10Kv cap with a .00047 15Kv cap from Just Radios.
It liiks like I could remove the cage portion by unscrewing it from the chassis, removing the flyback mounting screws, and the 1 screw holding the phenolic standoff. Once that is removed I can access the the electrical parts. Here's where I could use some help. I'm thinking of removing the wires from the flyback phenolic board and releasing the clips on the 1B3GT tube socket to completely remove the "guts" so I can work on them on the bench. My other option is to unsolder the flyback wires from underneath the chassis instead of from the flyback board. I've included close up pictures of what I have to work with. Also there is a very small separation of the flyback tape on the top of the flyback. Should I look at repairing this or just leave it alone? What should I use to clean the whole thing off with? I usually use some rubbing alcohol, Q-tips, etc. While I have it out, is there anything else that needs to be done to it? Thanks. ![]() ![]()
Last edited by Crist Rigott; 12-04-2016 at 01:32 AM. |
![]() |
| Thread Tools | |
| Display Modes | |
|
|