Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Antique Radio

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 06-07-2016, 12:35 PM
TUD1 TUD1 is offline
VideoKarma Member
 
Join Date: Jan 2014
Posts: 1,616
I once had a Philco 6X5GT short out and nearly destroyed the transformer. I caught it just in time.
Reply With Quote
  #2  
Old 06-07-2016, 09:36 PM
Jeffhs's Avatar
Jeffhs Jeffhs is offline
<----Zenith C845
 
Join Date: Feb 2003
Location: Fairport Harbor, Ohio (near Lake Erie)
Posts: 4,035
The pushbuttons could well be station presets, as were (and still are) used on car radios. These presets were on one side of the radio dial in the Zenith sets; the buttons on the other side were for a tone control arrangement Zenith called, IIRC, the "Radiorgan". Some Zenith tabletop sets had the presets in a horizontal row just beneath the tuning dial. I seem to remember one such radio that did have the presets in this position.

BTW, I am fairly sure the model number of the Zenith radio being discussed here is 8-S-463, not 8-5-463.
__________________
Jeff, WB8NHV

Collecting, restoring and enjoying vintage Zenith radios since 2002

Zenith. Gone, but not forgotten.
Reply With Quote
  #3  
Old 06-10-2016, 07:01 PM
Captainclock Captainclock is offline
Banned
 
Join Date: Dec 2013
Location: Elkhart, Indiana
Posts: 1,189
Just so everyone knows it was actually someone on here that told me that the "GT" version of the 6X5 tube was actually a good tube to use in such circuits because they were less suseptible to shorting than the 6X5G was, and I actually have an old 1940s Philco Console that uses a 6X5GT as a rectifier and although I haven't had a chance to power it up yet because it had a mouse nest in it and the mice chewed through some of the wiring in the radio, I'm apted to believe that what that person said about the 6X5GT is true. By the way, from what I heard from this person is that there were two different grid arrangements for the 6X5 tube and the 6X5G tube and some of the early 6X5GTs used an "X" shaped grid (think of the later 6X4 or the 6CA4 which were the later replacements of the 6X5 tube), but then later on once tube manufacturers realized the fatal flaw of the 6X5 tube they redesigned the tube (the 6X5GT as the 6X5Gs were no longer being made at that time) so that it had inline grids instead of "X" Shaped Grids which made the tubes more reliable, at least until the 6X4 and the 6CA4 came out to replace the 6X5GT tube.

Last edited by Captainclock; 06-10-2016 at 08:49 PM.
Reply With Quote
  #4  
Old 06-10-2016, 07:08 PM
Captainclock Captainclock is offline
Banned
 
Join Date: Dec 2013
Location: Elkhart, Indiana
Posts: 1,189
Quote:
Originally Posted by TUD1 View Post
I once had a Philco 6X5GT short out and nearly destroyed the transformer. I caught it just in time.
Did that 6X5GT tube have the "X" shaped Grids or did it look like the one in the picture below? I'm asking because the 6X5s that had the "X" shaped grids were the ones that were more suseptible to dead shorting whereas the ones that had the grids that were inline like the one pictured below are less suseptible to dead shorts, that's what I was told anyways.
Attached Images
File Type: jpg DSCN2839.jpg (55.2 KB, 11 views)

Last edited by Captainclock; 06-10-2016 at 07:19 PM.
Reply With Quote
  #5  
Old 06-10-2016, 09:35 PM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
Quote:
Originally Posted by Captainclock View Post
Did that 6X5GT tube have the "X" shaped Grids or did it look like the one in the picture below? I'm asking because the 6X5s that had the "X" shaped grids were the ones that were more suseptible to dead shorting whereas the ones that had the grids that were inline like the one pictured below are less suseptible to dead shorts, that's what I was told anyways.
I've had the flat plate ones short on me in an EICO audio signal generator (both the one in it and it's replacement that tested good before installation, but not after). Never tried the X ones, but I'd assume they were better than the flat plates since the later 6X4 and 6AC4 used and those and were considered more reliable than the 6X5.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
Audiokarma
  #6  
Old 06-11-2016, 08:43 AM
init4fun's Avatar
init4fun init4fun is offline
VideoKarma Member
 
Join Date: Mar 2011
Posts: 1,210
Quote:
Originally Posted by Electronic M View Post
I've had the flat plate ones short on me in an EICO audio signal generator (both the one in it and it's replacement that tested good before installation, but not after). Never tried the X ones, but I'd assume they were better than the flat plates since the later 6X4 and 6AC4 used and those and were considered more reliable than the 6X5.
Of course your correct here , the ones with the "X" shaped plates are the preferred ones to use if your going to use a 6X5 , as you rightly say the 6X4 and 6CA4 being the later model 7 and 9 pin replacement for what was the final improvement of the 6X5 design , the X shaped plates . In that transition they must have done something about improving the heater to cathode insulation , the way I always found the "flat plate" ones to be shorted . The 6Z4 , formerly known as 84 , was the first of these type of dual diodes and it was never pushed very hard with respect to it's H/K breakdown voltage since it was designed for the first vibrator power supply car radios (that replaced dynomotor powered ones in the early 1930s) and these were under 200 volt applications . The 6Z4/84 was the old large 6 pin base used before the Octals came to be , and when the Octals were introduced the 0Z4 was introduced along with them for car radio rectifier service , as we all know it's a Gas filled full wave rectifier that needed no heater at all . The trouble for the 6X5 started , in my opinion , when it was coupled to transformer supplies with 350 or more volts being pushed through a design that originally would have seen barely 200 .....

Last edited by init4fun; 06-11-2016 at 08:49 AM.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:46 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.