![]() |
|
|
|
#1
|
||||
|
||||
|
Quote:
I don't know where you saw that Emerson logo. I looked at the ballast tube and didn't see anything but a perforated cylinder over the tube itself; there was no logo on that cylinder, unless I was looking at the wrong part. BTW, this is the first TV I've ever seen that uses a ballast tube in the power supply. Every set I've ever worked on has had a power transformer and at least one 5U4 rectifier, or series string filaments with seleniums. That this set uses a ballast tube probably dates it to the late 1940s--'47 or '48. By 1950, however, I am sure the 5U4 had taken hold as the rectifier tube of choice in most TVs, although my folks' second set, a 1955 Crosley Super V 21" b&w console, still used selenium B+ rectifiers. That set had two such rectifiers, probably wired in parallel across the output of the B+ supply. The plate voltage for the tubes was probably taken directly from the output of the rectifiers and fed through at least one filter capacitor.
__________________
Jeff, WB8NHV Collecting, restoring and enjoying vintage Zenith radios since 2002 Zenith. Gone, but not forgotten. |
|
#2
|
||||
|
||||
|
Transformer is only for filaments.. set is HOT.. pair of doublers for B+ and B-
|
|
#3
|
||||
|
||||
|
Quote:
jr Last edited by jr_tech; 05-19-2016 at 10:01 PM. |
|
#4
|
||||
|
||||
|
I did not study it real closely...BUT I thought I saw a cap connected wrong--for a doubler--and perhaps a couple MORE backwards on the filter section?
|
|
#5
|
||||
|
||||
|
I think so also... looks to me like all 3 of the electrolytics in the 25Z6 negative supply are backwards.
jr |
| Audiokarma |
|
#6
|
||||
|
||||
|
Not the FIRST time I have seen that in a diagram. IIRC...the diagram for my 48-700 had one or more electros wired BACKWARDS..for the HV supply...
Don't they PROOFREAD these diagrams--before they are published ? I would expect TODAY...maybe not..but back THEN..when people took MUCH more pride in what they did..they would have triple-checked for errors.. Last edited by rca2000; 05-19-2016 at 10:36 PM. Reason: More info. |
|
#7
|
|||
|
|||
|
Quote:
The power supply was the only repair that our set had in four years of use. Emerson built a projector set, that used the same basic chassis, per Riders. |
|
#8
|
|||
|
|||
|
I stumbled across this old post, and wanted to add some information. The first Emerson TV was the 545, which had a power transformer. The cheaper 571 had the hot chassis, with all of those 25Z6 rectifier tubes. The incoming AC is doubled to about 250, and is also rectified to give a negative 125 volts or so. This gives about 375 volts end to end, to supply the deflection circuits. For the next production of that chassis type, Emerson replaced the tube rectifiers with seleniums.
I wanted to add this information, in case anyone here gets to work on one of those old beasts. I have owned an early 571 for 40+ years! |
|
#9
|
|||
|
|||
|
Quote:
The first set, my parents bought was the TV only model, using that type chassis. A smaller type console, where the speaker was as large as the picture. The ballast was for surge limiting of the two power supplies. The CRT went weak, when the set was about four years old. They gave it to me, to take it apart when I was about ten years old. Regarding the Crosley set, that model used a voltage doubler, two seleniums and a voltage doubling cap, before the two rectifiers and two caps and a choke to furnish the B+ voltages. It also used the audio output tube as a voltage divider. I common scheme that many manufacturers used. |
![]() |
| Thread Tools | |
| Display Modes | |
|
|