Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Flat Panels & Digital Format

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 05-03-2016, 07:34 PM
jr_tech's Avatar
jr_tech jr_tech is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 4,573
Are both tinned/soldered ends of the fuse exposed well enough that you can get your ohm meter probes on them? If the fuse is good, you should measure close to 0 ohms from end to end.

jr
Reply With Quote
  #2  
Old 05-03-2016, 08:03 PM
Captainclock Captainclock is offline
Banned
 
Join Date: Dec 2013
Location: Elkhart, Indiana
Posts: 1,189
Quote:
Originally Posted by jr_tech View Post
Are both tinned/soldered ends of the fuse exposed well enough that you can get your ohm meter probes on them? If the fuse is good, you should measure close to 0 ohms from end to end.

jr
I have no idea what the fuse's leads are like because I haven't had a chance to remove the circuit board out of the TV yet. I can get you a picture of the circuit board in question and circle the fuse on it for you so you can see what the fuse looks like. Below is a picture of the whole power supply/inverter board assembly and the second picture is a close-up shot showing the fuse that this TV uses, which like I said is a rather unusal style of fuse.
Attached Images
File Type: jpg DSCN2806.jpg (108.5 KB, 34 views)
File Type: jpg DSCN2807.jpg (90.4 KB, 26 views)

Last edited by Captainclock; 05-03-2016 at 08:14 PM.
Reply With Quote
  #3  
Old 05-03-2016, 08:13 PM
jr_tech's Avatar
jr_tech jr_tech is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 4,573
Yes that might help, if you can get a clear shot.

jr
update: looks like you should be able to get to the terminal on the other side of the board and measure it... or unsolder it if necessary.

Last edited by jr_tech; 05-03-2016 at 08:20 PM. Reason: add info
Reply With Quote
  #4  
Old 05-03-2016, 08:30 PM
Captainclock Captainclock is offline
Banned
 
Join Date: Dec 2013
Location: Elkhart, Indiana
Posts: 1,189
Quote:
Originally Posted by jr_tech View Post
Yes that might help, if you can get a clear shot.

jr
update: looks like you should be able to get to the terminal on the other side of the board and measure it... or unsolder it if necessary.
Well I measured the fuse and it seems that it might be open possibly because it measures about 2 ohms and not 0 ohms like you said it should if it weren't blown. good news is that the fuses this thing takes are still available over at mouser for like 11 cents a piece. So it shouldn't be too hard to replace the fuse (although they have the fuse glued into place with that nasty white glue that turns to a rubbery consistency when it dries so it will be tricky to try and get it out of the circuit without damaging the circuit board traces.) What's a good way to get rid of that glue without damaging anything?
Reply With Quote
  #5  
Old 05-03-2016, 08:36 PM
jr_tech's Avatar
jr_tech jr_tech is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 4,573
I stated "close to 0 ohms" ... IMHO 2 ohms is likely close enough, but for a better measurment, you should remove it from the board. I usually use a small exacto knife or scalpel to carefully cut away most of the rubbery glue.

jr

Last edited by jr_tech; 05-03-2016 at 08:39 PM. Reason: add info
Reply With Quote
Audiokarma
  #6  
Old 05-04-2016, 04:13 AM
Captainclock Captainclock is offline
Banned
 
Join Date: Dec 2013
Location: Elkhart, Indiana
Posts: 1,189
Quote:
Originally Posted by jr_tech View Post
I stated "close to 0 ohms" ... IMHO 2 ohms is likely close enough, but for a better measurment, you should remove it from the board. I usually use a small exacto knife or scalpel to carefully cut away most of the rubbery glue.

jr
OK, well the closest thing I have to an exacto knife is a box cutter and that's it. Which I'm assuming a box cutter will do the same thing as an exacto knife except not as precise as an exacto knife. anyways if you had to guess as to which capacitors on the power supply board would be bad which ones would you suspect first? The ones closest to the back of the board or the ones in the middle or the large electrolytic capacitor?

Also I've never seen a LCD TV with 6 inverter connections before, I've seen them with 2 or 4 inverter connections but never 6 connections and certainly never on one side of the LCD Panel before, usually the inverter connections are at the top and the bottom of the inverter board but this is the first time I've seen the inverter connections come out on one side of the board. Is there some sort of advantage to doing it on one side of the inverter board as opposed to the traditional way of doing it with the connections coming out of the top and bottom of the inverter board? Could this possibly be an early LED TV?
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:37 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.